- 您现在的位置：买卖IC网 > PDF目录196394 > TDA7572 (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PQFP64 PDF资料下载
参数资料
| 型号： | TDA7572 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 封装： | ROHS COMPLIANT, HIQUAD-64 |
| 文件页数： | 37/64页 |
| 文件大小： | 1052K |
| 代理商： | TDA7572 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
Modulator
TDA7572
Pulse injection is being used with the clocked PWM scheme to prevent missing pulses from
an over-modulation condition. The minimum pulse width is dynamically determined by
looking at the delay from the comparator output to the actual switching of the FET stage.
This delay is used to extend any pulses from the modulator that would otherwise be too
short. Circuitry is provided to keep the integrator hovering near the level at which limiting
first occurred, which prevents transients once we leave the over modulation condition. This
is done by summing in a current that is proportional to the amount of time that the pulse is
extended.
Since only three- state modulation is supported, it may prove necessary to slightly delay the
clock going to one modulator to prevent the noise from the switching of one modulator
affecting the second modulator when there is no audio input. This can be done with a small
RC on the clock feeding one modulator. The same result could be obtained adding the RC
on the feedback feeding one modulator.
The reference voltage of the modulator changes from SVR at it's input, to Vcc/2 at its output.
This allows output signal to be centered between the supply rails, increasing unclipped
output voltage swing by preventing asymmetric clipping. This is accomplished using the
LVLSFT pin, as described in the previous paragraph. It has been pointed out that there is
potential for abrupt transients at the output stage, as this scheme will attempt to have the
outputs track VCC/2, while it may be better for avoiding pops to have them rise slowly with
SVR. The end user needs to make this decision by making or not the connection between
HVCC and LVLSFT pin. Will not be present pop noise in a system with perfect symmetry
between the two modulators branch. Pop noise will rise with increasing of asymmetry.
7.1
FET drive
Gate drive circuits are provided to drive complementary external FETS. An internal regulator
to supply the low side gate drivers provides a voltage 10V above VSM. This fully enhances
the FETs without exceeding their VGS limits. A separate regulator 10V below VSP, is used
for the high side gate drivers.
Shoot-through is prevented by sensing VGS of each FET with a dedicated sense line
(GateSensing), and blocking the opposite FET turn-on if the active FET in a bridge has a
|VGS|> |VThreshold|. This allows discrete components to be used to adjust gate charging
without concern over shoot-through.
The drivers are capable to provide high current for a short time (about 5s) and a lower
current after this time(~150mA). This is done to give enough charge current at the
commutation and avoid short-cut overcurrent.
The VDS of the enhanced FET of each bridge is used monitor current and detect
overcurrent condition. The sensed VDS signal is blanked such that sensing is only active
when the FET is enhanced and any turn on transients have settled. There are two type of
overcurrent intervention: current limitation, cycle-by-cycle limitation. The current limitation
Table 32.
PWMClock table
PWMClock [1:0]
Ratio
Nominal frequency
00
FNOM/2
55KHz
01
FNOM
110KHz
10
FNOM*2
220KHz
11
FNOM
110KHz
相关PDF资料 |
PDF描述 |
|---|---|
| TDSO1160-KL | 7 SEG NUMERIC DISPLAY, ORANGE RED, 7 mm |
| TE-4Q4TM2MH2% | 1 ELEMENT, 2000 uH, GENERAL PURPOSE INDUCTOR |
| TD-4Q3TA2H+/-1% | 1 ELEMENT, 2000000 uH, GENERAL PURPOSE INDUCTOR |
| TD-5Q4TW10MH+/-1% | 1 ELEMENT, 10000 uH, GENERAL PURPOSE INDUCTOR |
| TD-5Q4TW100MH+/-1% | 1 ELEMENT, 100000 uH, GENERAL PURPOSE INDUCTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TDA7572TR | 功能描述:音频放大器 200W Mono Bridge PWM Amplifier Built-In RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TDA7575 | 功能描述:音频放大器 MULTI F DUAL AMP RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TDA7575B | 功能描述:音频放大器 2 x 75W Multifunct Dual-Bridge Pwr Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TDA7575BPD | 功能描述:音频放大器 2 x 75W Multifunct Dual-Bridge Pwr Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TDA7575BPDTR | 功能描述:音频放大器 2 x 75W Multifunct Dual-Bridge Pwr Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。