参数资料
型号: THS1007IDA
厂商: TEXAS INSTRUMENTS INC
元件分类: ADC
英文描述: 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
封装: GREEN, PLASTIC, TSSOP-32
文件页数: 21/34页
文件大小: 364K
代理商: THS1007IDA
THS1007
SLAS286B AUGUST 2000 REVISED DECEMBER 2010
www.ti.com
28
ANALOG INPUT CONFIGURATION AND REFERENCE VOLTAGE
The THS1007 features four analog input channels. These can be configured for either single-ended or
differential operation. Figure 36 shows a simplified model, where a single-ended configuration for channel AINP
is selected. The reference voltages for the ADC itself are VREFP and VREFM (either internal or external reference
voltage). The analog input voltage range is between VREFM to VREFP. This means that VREFM defines the
minimum voltage, and VREFP defines the maximum voltage, which can be applied to the ADC. The internal
reference source provides the voltage VREFM of 1.5 V and the voltage VREFP of 3.5 V (see also section
reference voltage). The resulting analog input voltage swing of 2 V can be expressed by:
VREFM v AINP v VREFP
(1)
10-Bit
ADC
VREFP
VREFM
AINP
Figure 36. Single-Ended Input Stage
A differential operation is desired in many applications due to a better signal-to-noise ration. Figure 37 shows
a simplified model for the analog inputs AINM and AINP, which are configured for differential operation. The
differential operation mode provides in terms of performance benefits over the single-ended mode and is
therefore recommended for best performance. The THS1007 offers 2 differential analog inputs and in the
single-ended mode4 analog inputs. If the analog input architecture is different, common-mode voltages can be
rejected. Additional details for both modes are given below.
10-Bit
ADC
VREFP
VREFM
AINP
Σ
VADC
AINM
+
Figure 37. Differential Input Stage
In comparison to the single-ended configuration it can be seen that the voltage VADC, which is applied at the
input of the ADC, is the difference between the input AINP and AINM. The voltage VADC can be calculated as
follows:
VADC + ABS(AINP–AINM)
(2)
An advantage to single-ended operation is that the common-mode voltage
(3)
VCM +
AINM ) AINP
2
can be rejected in the differential configuration, if the following condition for the analog input voltages is true:
(4)
AGND v AINM, AINP v AVDD
(5)
1V v VCM v 4V
SINGLE-ENDED MODE OF OPERATION
The THS1007 can be configured for single-ended operation using dc or ac coupling. In either case, the input
of the THS1007 must be driven from an operational amplifier that does not degrade the ADC performance.
Because the THS1007 operates from a 5-V single supply, it is necessary to level-shift ground-based bipolar
signals to comply with its input requirements. This can be achieved with dc and ac-coupling.
相关PDF资料
PDF描述
THS1007IDAR 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
THS1007IDAG4 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
THS10082CDAG4 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
THS10082CDAR 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
THS10082CDA 2-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
相关代理商/技术参数
参数描述
THS1007IDAG4 功能描述:模数转换器 - ADC 10-Bit 6MSPS Simult Sampling Quad Ch RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
THS1007IDAR 制造商:TI 制造商全称:Texas Instruments 功能描述:10-BIT, 4 ANALOG INPUT, 6-MSPS, SIMULATANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER
THS10082 制造商:TI 制造商全称:Texas Instruments 功能描述:10 bit TWO ANALOG INPUT, 8 MSPS SIMULTANEOUS SAMPLING ANALOG TO DIGITAL CONVERTER
THS10082CDA 功能描述:模数转换器 - ADC 10 Bit 8 MSPS Lo-Pwr RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
THS10082CDAG4 功能描述:模数转换器 - ADC 10 Bit 8 MSPS Lo-Pwr RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32