- 您现在的位置：买卖IC网 > PDF目录98219 > THS1230IDWRG4 (TEXAS INSTRUMENTS INC) 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 PDF资料下载
参数资料
| 型号： | THS1230IDWRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | ADC |
| 英文描述： | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| 封装： | GREEN, PLASTIC, SOIC-28 |
| 文件页数： | 6/25页 |
| 文件大小： | 854K |
| 代理商： | THS1230IDWRG4 |
www.ti.com
VIN+
VIN
R1
R2
+
R1
R2
+
C1
C2
THS1230
AIN+
AIN
REFT
REFB
AVDD
2
THS1230
SLAS291B – OCTOBER 2000 – REVISED MARCH 2004
The analog input of the THS1230 is a differential input that can be configured in various ways depending on the
signal source and the required level of performance. A fully differential connection (see Figure 17) delivers the
best performance from the converter.
Figure 17. AC-Coupled Differential Input
The analog input can be dc-coupled (see Figure 18) as long as the inputs are within the analog input common
mode voltage range. For example (see Figure 18), V+ and V– are signals centered on GND with a peak-to-peak
voltage of 2 V, and the circuit in Figure 18 is used to interface it with the THS1230. Assume AVDD of the
converter is 3 V. Two problems have to be solved. The first is to shift common mode level (CML) from 0 V to 1.5
V (AVDD/2). To do that, a V bias voltage and an adequate ratio of R1 and R2 have to be selected. For instance, if
V bias = AVDD = 3 V, then R1 = R2. The second is that the differential voltage has to be reduced from 4 V (2 x 2
V) to 1 V, and for that an attenuation of 4 to1 is needed. The attenuation is determined by the relation:
(R3||2R2)/((R3||2R2) + 2R1). One possible solution is R1 = R2 = R3 = 150
. In this case, moreover, the input
impedance (2R1 + (R3||2R2)) will be 400
. The values can be changed to match any other input impedance. A
capacitor, C, connected from AIN+ to AIN– helps filter any high frequency noise on the inputs, also improving
performance. Note that the chosen value of capacitor C must take into account the highest frequency component
of the analog input signal.
14
相关PDF资料 |
PDF描述 |
|---|---|
| THS1230IDW | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1230IDWR | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1230IDWG4 | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1230IPWG4 | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1230CPW | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| THS1230IPW | 功能描述:模数转换器 - ADC Low Power High-Speed ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| THS1230IPWG4 | 功能描述:模数转换器 - ADC Low Power High-Speed ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| THS1230IPWR | 功能描述:模数转换器 - ADC Low Power High-Speed ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| THS1230IPWRG4 | 功能描述:模数转换器 - ADC Low Power High-Speed ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| THS124 | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:HIGH STABILITY MOTOR CONTROL. DIGITAL TACHOMETER. CRANK SHAFT POSITION SENSOR. |
发布紧急采购，3分钟左右您将得到回复。