- 您现在的位置：买卖IC网 > PDF目录98220 > THS3001HVIDGNRG4 (TEXAS INSTRUMENTS INC) 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 PDF资料下载
参数资料
| 型号： | THS3001HVIDGNRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| 封装： | GREEN, PLASTIC, MSOP-8 |
| 文件页数： | 16/38页 |
| 文件大小： | 875K |
| 代理商： | THS3001HVIDGNRG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
2
4
6
8
1M
f Frequency Hz
1
3
5
7
100k
10M
100M
0
Output
Amplitude
dB
1
1G
Gain = 1
VCC = ±15 V
VO = 200 mV RMS
CI = 10 pF
CI = Stray C Only
+
1 k
RL =
150
Cin
Vin
Vout
1 k
50
2
0
2
4
1M
f Frequency Hz
3
1
3
100k
10M
100M
4
6
Output
Amplitude
dB
5
7
1G
Gain = 1
VCC = ±15 V
VO = 200 mV RMS
CI = 1 pF
CI = 0 pF
(Stray C Only)
+
1 k
50
RL =
150
Cin
Vin
Vout
www.ti.com................................................................................................................................................. SLOS217H – JULY 1998 – REVISED SEPTEMBER 2009
PCB DESIGN CONSIDERATIONS
Proper PCB design techniques in two areas are important to ensure proper operation of the THS3001. These
areas are high-speed layout techniques and thermal-management techniques. Because the THS3001 is a
high-speed part, the following guidelines are recommended.
Ground plane - It is essential that a ground plane be used on the board to provide all components with a low
inductive ground connection, but should be removed from below the output and negative input pins as noted
below.
The DGN package option includes a thermal pad for increased thermal performance. When using this
package, it is recommended to distribute the negative supply as a power plane, and tie the thermal pad to this
supply with multiple vias for proper power dissipation. It is not recommended to tie the thermal pad to ground
when using split supply (±V) as this will cause worse distortion performance than shown in this data sheet.
Input stray capacitance - To minimize potential problems with amplifier oscillation, the capacitance at the
inverting input of the amplifiers must be kept to a minimum. To do this, PCB trace runs to the inverting input
must be as short as possible, the ground plane must be removed under any etch runs connected to the
inverting input, and external components should be placed as close as possible to the inverting input. This is
especially true in the noninverting configuration. An example of this can be seen in Figure 53, which shows
what happens when a 1-pF capacitor is added to the inverting input terminal. The bandwidth increases at the
expense of peaking. This is because some of the error current is flowing through the stray capacitor instead
of the inverting node of the amplifier. Although, while the device is in the inverting mode, stray capacitance at
the inverting input has a minimal effect. This is because the inverting node is at a virtual ground and the
voltage does not fluctuate nearly as much as in the noninverting configuration. This can be seen in Figure 54,
where a 10-pF capacitor adds only 0.35 dB of peaking. In general, as the gain of the system increases, the
output peaking due to this capacitor decreases. While this can initially look like a faster and better system,
overshoot and ringing are more likely to occur under fast transient conditions. So proper analysis of adding a
capacitor to the inverting input node should be performed for stable operation.
OUTPUT AMPLITUDE
vs
FREQUENCY
Figure 53.
Figure 54.
Proper power-supply decoupling - Use a minimum 6.8-
μF tantalum capacitor in parallel with a 0.1-μF ceramic
capacitor on each supply terminal. It may be possible to share the tantalum among several amplifiers
depending on the application, but a 0.1-
μF ceramic capacitor should always be used on the supply terminal of
every amplifier. In addition, the 0.1-
μF capacitor should be placed as close as possible to the supply terminal.
As this distance increases, the inductance in the connecting etch makes the capacitor less effective. The
designer should strive for distances of less than 0.1 inch between the device power terminal and the ceramic
capacitors.
Copyright 1998–2009, Texas Instruments Incorporated
23
Product Folder Link(s): THS3001
相关PDF资料 |
PDF描述 |
|---|---|
| THS3001IDG4 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3001IDRG4 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3001HVCDGNRG4 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3001HVCDGNR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3001HVCDR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| THS3001ID | 功能描述:高速运算放大器 420MHz Current RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| THS3001ID | 制造商:Texas Instruments 功能描述:IC SM OP-AMP HIGH SPEED CFB |
| THS3001ID | 制造商:Texas Instruments 功能描述:OP AMP HIGH SPEED CFB SMD 3001 |
| THS3001IDG4 | 功能描述:高速运算放大器 420-MHz Curr Feedback Amp RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| THS3001IDGN | 功能描述:高速运算放大器 420-MHz Curr Feedback Amp RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。