- 您现在的位置：买卖IC网 > PDF目录98224 > THS4022IDRG4 (TEXAS INSTRUMENTS INC) 2 CHANNEL, VIDEO AMPLIFIER, PDSO8 PDF资料下载
参数资料
| 型号： | THS4022IDRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 2 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| 封装： | PLASTIC, MS-012AA, SOIC-8 |
| 文件页数： | 7/28页 |
| 文件大小： | 922K |
| 代理商： | THS4022IDRG4 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
www.ti.com
General Thermal Pad Design Considerations
DIE
SideView(a)
EndView(b)
BottomView(c)
DIE
Thermal
Pad
M0031-01
Thermalpadarea=68mils
70mils(1.73mm 1.78mm)with5vias.
Viadiameter=13mils(0.33mm).
M0032-02
SLOS265C – SEPTEMBER 1999 – REVISED JULY 2007
The THS402x is available packaged in a thermally-enhanced DGN package, which is a member of the
PowerPAD family of packages. This package is constructed using a downset leadframe upon which the die is
mounted [see Figure 37(a) and Figure 37(b)]. This arrangement results in the lead frame being exposed as a
thermal pad on the underside of the package [see Figure 37(c)]. Because this thermal pad has direct thermal
contact with the die, excellent thermal performance can be achieved by providing a good thermal path away from
the thermal pad.
The PowerPAD package allows for both assembly and thermal management in one manufacturing operation.
During the surface-mount solder operation (when the leads are being soldered), the thermal pad can also be
soldered to a copper area underneath the package. Through the use of thermal paths within this copper area,
heat can be conducted away from the package into either a ground plane or other heat dissipating device.
The PowerPAD package represents a design breakthrough, combining the small area and ease of the surface
mount assembly method to eliminate the previously difficult mechanical methods of heatsinking.
NOTE: The thermal pad is electrically isolated from all terminals in the package.
Figure 37. Views of Thermally Enhanced DGN Package
Although there are many ways to heatsink this device properly, the following steps illustrate the recommended
approach.
Figure 38. Thermal Pad PCB Etch and Via Pattern
1. Prepare the PCB with a top side etch pattern as shown in Figure 38. There should be etch for the leads as
well as etch for the thermal pad.
2. Place five holes in the area of the thermal pad. These holes should be 13 mils (0.33 mm) in diameter. Keep
them small so that solder wicking through the holes is not a problem during reflow.
3. Additional vias may be placed anywhere along the thermal plane outside of the thermal pad area. These vias
help dissipate the heat generated by the THS402xDGN IC. These additional vias may be larger than the
13-mil (0.33-mm) diameter vias directly under the thermal pad. They can be larger because they are not in
the thermal pad area to be soldered, so wicking is not a problem.
4. Connect all holes to the internal ground plane.
5. When connecting these holes to the ground plane, do not use the typical web or spoke via connection
methodology. Web connections have a high thermal resistance connection that is useful for slowing the heat
transfer during soldering operations. This makes the soldering of vias that have plane connections easier. In
this application, however, low thermal resistance is desired for the most efficient heat transfer. Therefore, the
holes under the THS402xDGN package should connect to the internal ground plane with a complete
connection around the entire circumference of the plated-through hole.
6. The top-side solder mask should leave the terminals of the package and the thermal pad area with its five
holes exposed. The bottom-side solder mask should cover the five holes of the thermal pad area. This
prevents solder from being pulled away from the thermal pad area during the reflow process.
Copyright 1999–2007, Texas Instruments Incorporated
15
相关PDF资料 |
PDF描述 |
|---|---|
| THS4021CDRG4 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4061IDGN | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4061MFK | 1 CHANNEL, VIDEO AMPLIFIER, CQCC20 |
| THS4062CDGNRG4 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4061IDGNG4 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| THS4031 | 制造商:TI 制造商全称:Texas Instruments 功能描述:100-MHz LOW-NOISE HIGH-SPEED AMPLIFIERS |
| THS4031CD | 功能描述:高速运算放大器 100MHz Low Noise RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| THS4031CD | 制造商:Texas Instruments 功能描述:IC SM OP-AMP 100MHZ |
| THS4031CDG4 | 功能描述:高速运算放大器 100-MHz Low Noise Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| THS4031CDGN | 功能描述:高速运算放大器 100-MHz Low Noise Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。