- 您现在的位置：买卖IC网 > PDF目录20928 > TLC5945RHBT (Texas Instruments)IC LED DRIVER LINEAR 32-QFN PDF资料下载
参数资料
| 型号： | TLC5945RHBT |
| 厂商： | Texas Instruments |
| 文件页数： | 14/30页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER LINEAR 32-QFN |
| 标准包装： | 250 |
| 恒定电流： | 是 |
| 拓扑： | PWM |
| 输出数： | 16 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 颜色 |
| 频率： | 30MHz |
| 电源电压： | 3 V ~ 5.5 V |
| 输出电压： | 17V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
TLC5945
www.ti.com
SLVS755 – MARCH 2007
POWER DISSIPATION CALCULATION
The device power dissipation needs to be below the power dissipation rate of the device package to ensure
correct operation. Equation 7 calculates the power dissipation of device:
P
D
+ V
CC
I
CC
) V
OUT
I
MAX
N
DCn
63
d
PWM
(7)
where:
V CC : device supply voltage
I CC : device supply current
V OUT : TLC5945 OUTn voltage when driving LED current
I MAX : LED current adjusted by R (IREF) Resistor
DC n : maximum dot correction value for OUTn
N: number of OUTn driving LED at the same time
d PWM : duty cycle defined by BLANK pin or GS PWM value
OPERATING MODES
The TLC5945 has two operating modes defined by MODE as shown in Table 4 . The GS and DC registers are
set to random values that are not known just after power on. The GS and DC values must be programmed
before turning on the outputs. Please note that when initially setting GS and DC data after power on, the GS
data must be set before the DC data is set. Failure to set GS data before DC data may result in the first bit of
GS data being lost. XLAT must be low when the MODE pin goes high-to-low or low-to-high to change back and
forth between GS mode and DC mode.
Table 4. TLC5945 Operating Modes Truth Table
MODE
GND
V CC
INPUT SHIFT REGISTER
192 bit
96 bit
OPERATING MODE
Grayscale PWM Mode
Dot Correction Data Input Mode
SETTING DOT CORRECTION
The TLC5945 has the capability to fine-adjust the output current of each channel (OUT0 to OUT15)
independently. This is also called dot correction. This feature is used to adjust the brightness deviations of LEDs
connected to the output channels OUT0 to OUT15. Each of the 16 channels can be programmed with a 6-bit
word. The channel output can be adjusted in 64 steps from 0% to 100% of the maximum output current I max . The
TEST pin must be connected to VCC to ensure proper operation of the dot correction circuitry. Equation 8
determines the output current for each output n:
I
OUTn
+ I max
DCn
63
(8)
where:
I max = the maximum programmable output current for each output.
DCn = the programmed dot correction value for output n (DCn = 0 to 63).
n = 0 to 15
14
Submit Documentation Feedback
相关PDF资料 |
PDF描述 |
|---|---|
| P51-75-A-J-MD-4.5OVP-000-000 | SENSOR 75PSI 3/8-24UNF .5-4.5V |
| P51-500-S-Z-P-4.5V-000-000 | SENSOR 500PSI 1/4-18NPT .5-4.5V |
| KHR 2-T227 150.0 OHM 1% | RES 150 OHM 200W 1% TO-227 |
| GPFC250-15 | POWER SUP SWITCHER 250W 15V PFC |
| REC3-123.3DRW/H2/A/CTRL | CONV DC/DC 3W 9-18VIN +/-3.3VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TLC5945RHBTG4 | 功能描述:LED显示驱动器 16-Ch LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| TLC5946 | 制造商:TI 制造商全称:Texas Instruments 功能描述:16-Channel, 12-Bit PWM LED Driver with 6-Bit Dot Correction |
| TLC5946_0806 | 制造商:TI 制造商全称:Texas Instruments 功能描述:16-Channel, 12-Bit PWM LED Driver with 6-Bit Dot Correction |
| TLC59461 | 制造商:TI 制造商全称:Texas Instruments 功能描述:16-Channel, 12-Bit PWM LED Driver with 6-Bit Dot Correction |
| TLC59461PWP | 功能描述:LED显示驱动器 16Ch 12B PWM LED Drvr 6B Dot Correc RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。