参数资料
型号: TLV990APFB
厂商: TEXAS INSTRUMENTS INC
元件分类: 消费家电
英文描述: SPECIALTY CONSUMER CIRCUIT, PQFP48
封装: PLASTIC, TQFP-48
文件页数: 10/24页
文件大小: 328K
代理商: TLV990APFB
TLV990A
3-V, 10-BIT, 28-MSPS AREA CCD AND VIDEO SIGNAL PROCESSOR
SLAS297 – SEPTEMBER 2000
18
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
device reset
When pin RESET (pin 29) is pulled low, all internal registers are set to their default values. The device also resets
itself when it is first powered on. In addition, the TLV990A has a software-reset function that resets the device
when writing a control bit to the control register.
See the
register definition section for the register default values.
voltage references
An internal precision-voltage reference of 1.5 V nominal is provided. This reference voltage is used to generate
the ADC Ref– voltage of 1 V and Ref+ of 2 V. It is also used to set the clamp voltage. All internally-generated
voltages are fixed values and cannot be adjusted.
power-down mode (standby)
The TLV990A implements both hardware and software power-down modes. Pulling pin STBY (pin 30) low puts
the device in the low-power standby mode. Total supply current drops to about 0.6 mA. Setting a power-down
control bit in the control register can also activate the power-down mode. The user can still program all internal
registers during the power-down mode.
power supply
The TLV990A has several power-supply pins. Each major internal analog block has a dedicated AVDD supply
pin. All internal digital circuitry is powered by DVDD. Both AVDD and DVDD are 3-V nominal.
The DIVDD and DIGND pins supply power to the output digital driver (D9–D0). The DIVDD is independent of the
DVDD and can be operated from 1.8 V to 4.4 V. This allows the outputs to interface with digital ASICs requiring
different supply voltages.
ground and decoupling
All ground pins of the TLV990A are not internally connected and must be connected externally to PCB ground.
General practices should apply to the PCB design to limit high-frequency transients and noise that are fed back
into the supply and reference lines. This requires that the supply and reference pins be sufficiently bypassed.
In the case of power supply decoupling, 0.1-
F ceramic chip capacitors are adequate to keep the impedance
low over a wide frequency range. Recommended external decoupling for the three voltage-reference pins is
shown in Figure 4. Since their effectiveness depends largely on the proximity to the individual supply pin, all
decoupling capacitors should be placed as close as possible to the supply pins.
To reduce high-frequency and noise coupling, it is highly recommended that digital and analog grounds be
shorted immediately outside the package. This can be accomplished by running a low-impedance line between
DGND and AGND under the package.
相关PDF资料
PDF描述
TLV990BPFB SPECIALTY CONSUMER CIRCUIT, PQFP48
TM21R-5A-3232-LP(50) 32 CONTACT(S), FEMALE, RIGHT ANGLE TELECOM AND DATACOM CONNECTOR, SOLDER, JACK
TM21R-5B-3232D-LP(50) 32 CONTACT(S), FEMALE, RIGHT ANGLE TELECOM AND DATACOM CONNECTOR, SOLDER, JACK
TM21R-5B-4848D-LP(50) 48 CONTACT(S), FEMALE, RIGHT ANGLE TELECOM AND DATACOM CONNECTOR, SOLDER, JACK
TM21R-5C-88(50) 8 CONTACT(S), FEMALE, RIGHT ANGLE TELECOM AND DATACOM CONNECTOR, SOLDER, JACK
相关代理商/技术参数
参数描述
TLV990B 制造商:TI 制造商全称:Texas Instruments 功能描述:3-V, 10-BIT, 28-MSPS AREA CCD AND VIDEO SIGNAL PROCESSOR
TLV990BPFB 功能描述:IC CCD SIGNAL PROC/DGTZR 48TQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模拟前端 (AFE) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:- 通道数:2 功率(瓦特):- 电压 - 电源,模拟:3 V ~ 3.6 V 电压 - 电源,数字:3 V ~ 3.6 V 封装/外壳:32-VFQFN 裸露焊盘 供应商设备封装:32-QFN(5x5) 包装:带卷 (TR)
TLV990PFB 制造商:TI 制造商全称:Texas Instruments 功能描述:3-V, 10-BIT, 28-MSPS AREA CCD AND VIDEO SIGNAL PROCESSOR
TLVAIC12KIRHBRG4 功能描述:接口—CODEC Lo-Pwr Mono Voice Band CODEC RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel
TLVAIC12KIRHBTG4 功能描述:接口—CODEC Lo-Pwr Mono Voice Band CODEC RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel