- 您现在的位置：买卖IC网 > PDF目录19533 > TMP141AIDGKTG4 (Texas Instruments)IC TEMP SENSOR DGTL OUT 8-MSOP PDF资料下载
参数资料
| 型号： | TMP141AIDGKTG4 |
| 厂商： | Texas Instruments |
| 文件页数： | 12/24页 |
| 文件大小： | 662K |
| 描述： | IC TEMP SENSOR DGTL OUT 8-MSOP |
| 标准包装： | 250 |
| 系列： | SensorPath™ |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部 |
| 感应温度： | -40°C ~ 125°C |
| 精确度： | ±3°C（最小值） |
| 拓扑： | ADC（三角积分型），寄存器库 |
| 输出类型： | 1 线 SensorPath? |
| 输出警报： | 无 |
| 输出风扇： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
TMP141
SBAS347A MARCH 2005 REVISED JULY 2006
www.ti.com
12
Register Ah: Temperature Control (Read/Write)
Bits 152: Reserved. These bits read as 0.
Bit 1, Enable Sensor (EN_S): Default is 0, which is the
disabled state. In addition to setting this bit, the enable bit
in register 5 must also be set in order to measure
temperature.
Bit 0, Attention Enable (AT_E): Default is disabled.
When this bit is set, and the sensor is enabled (bit 1), the
TMP141 will generate Attention Requests. If enabled, an
Attention Request will be generated when a bit is set in the
Device Status register (register 4). See Figure 5 for the
details on the conditions for generating an Attention
Request.
Note: A bus error always attempts to generate an Attention
Request.
(For more information on the Attention Request
conditions, see the flowcharts in Figure 4 and Figure 5,
and the information on Exception Handling on page 14.)
The rules for generating an Attention Request are
different, depending on whether it was caused by a bus
error or a temperature conversion. A bus error always
attempts to generate an Attention Request, whereas a
conversion or a conversion overrun has several conditions
that may prevent the assertion of Attention Request.
These differences are illustrated in Figure 4 and Figure 5.
Register 20h: Conversion Rate (Read/Write)
The conversion rate is controlled by both the low-power bit
in the Device Control register, and the Conversion Rate
setting in the Conversion Rate register. This register is
device-specific, and therefore not defined by the
SensorPath specification. The conversion rate for a given
application is chosen based on system requirements and
limitations, such as the thermal response time of the
system (including the TMP141).
Table 4. Conversion Time Settings
LOW-POWER
MODE
(register 5, bit 2)
CONVERSION
RATE SETTING
(register 20h, bits
10 binary)
TYPICAL
CONVERSION
TIME
(ms)
0
00
64
1
00
96
0
01
96
1
01
382
0
10
190 (default)
1
10
766
0
11
382
1
11
1532
相关PDF资料 |
PDF描述 |
|---|---|
| RDER72J333K3K1C11B | CAP CER 0.033UF 630V 10% RADIAL |
| EPM7128AEFC100-7N | IC MAX 7000 CPLD 128 100-FBGA |
| VI-B0Y-CY-F1 | CONVERTER MOD DC/DC 3.3V 33W |
| 2112-H-RC | INDUCTOR TORD HI AMP 100UH HORZ |
| HBM08DRXI | CONN EDGECARD 16POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TMP150 | 制造商:TRUMPOWER 制造商全称:Tumbler Technologies + TRUMPower 功能描述:150 WATT MEDICAL POWER ADAPTERS |
| TMP150-12 | 制造商:TRUMPOWER 制造商全称:Tumbler Technologies + TRUMPower 功能描述:150 WATT MEDICAL POWER ADAPTERS |
| TMP150-15 | 制造商:TRUMPOWER 制造商全称:Tumbler Technologies + TRUMPower 功能描述:150 WATT MEDICAL POWER ADAPTERS |
| TMP150-19 | 制造商:TRUMPOWER 制造商全称:Tumbler Technologies + TRUMPower 功能描述:150 WATT MEDICAL POWER ADAPTERS |
| TMP150-24 | 制造商:TRUMPOWER 制造商全称:Tumbler Technologies + TRUMPower 功能描述:150 WATT MEDICAL POWER ADAPTERS |
发布紧急采购，3分钟左右您将得到回复。