参数资料
型号: TMR320C2811ZHHA
厂商: Texas Instruments, Inc.
元件分类: 数字信号处理
英文描述: TMS320R2811, TMS320R2812 Digital Signal Processors
中文描述: TMS320R2811,TMS320R2812数字信号处理器
文件页数: 34/147页
文件大小: 2021K
代理商: TMR320C2811ZHHA
Functional Overview
34
June 2004
SPRS257
3.2.15
Low-Power Modes
R281x devices are full static CMOS devices. Three low-power modes are provided:
IDLE:
Place CPU into low-power mode. Peripheral clocks may be turned off selectively and only
those peripherals that need to function during IDLE are left operating. An enabled interrupt
from an active peripheral will wake the processor from IDLE mode.
Turn off clock to CPU and peripherals. This mode leaves the oscillator and PLL functional.
An external interrupt event will wake the processor and the peripherals. Execution begins
on the next valid cycle after detection of the interrupt event.
Turn off oscillator. This mode basically shuts down the device and places it in the lowest
possible power consumption mode. Only a reset or XNMI will wake the device from this
mode.
STANDBY:
HALT:
3.2.16
Peripheral Frames 0, 1, 2 (PFn)
R281x segregates peripherals into three sections. The mapping of peripherals is as follows:
PF0:
XINTF:
PIE:
Timers:
eCAN:
SYS:
GPIO:
EV:
McBSP:
SCI:
SPI:
ADC:
External Interface Configuration Registers (2812 only)
PIE Interrupt Enable and Control Registers Plus PIE Vector Table
CPU-Timers 0, 1, 2 Registers
eCAN Mailbox and Control Registers
System Control Registers
GPIO Mux Configuration and Control Registers
Event Manager (EVA/EVB) Control Registers
McBSP Control and TX/RX Registers
Serial Communications Interface (SCI) Control and RX/TX Registers
Serial Peripheral Interface (SPI) Control and RX/TX Registers
12-Bit ADC Registers
PF1:
PF2:
3.2.17
General-Purpose Input/Output (GPIO) Multiplexer
Most of the peripheral signals are multiplexed with general-purpose I/O (GPIO) signals. This enables the user
to use a pin as GPIO if the peripheral signal or function is not used. On reset, all GPIO pins are configured
as inputs. The user can then individually program each pin for GPIO mode or Peripheral Signal mode. For
specific inputs, the user can also select the number of input qualification cycles. This is to filter unwanted noise
glitches.
3.2.18
32-Bit CPU-Timers (0, 1, 2)
CPU-Timers 0, 1, and 2 are identical 32-bit timers with presettable periods and with 16-bit clock prescaling.
The timers have a 32-bit count down register, which generates an interrupt when the counter reaches zero.
The counter is decremented at the CPU clock speed divided by the prescale value setting. When the counter
reaches zero, it is automatically reloaded with a 32-bit period value. CPU-Timer 2 is reserved for Real-Time
OS (RTOS)/BIOS applications. CPU-Timer 2 is reserved for the DSP/BIOS real-time operating system
(DSP/BIOS RTOS), and is connected to INT14 of the CPU. CPU-Timer 1 is for general use, and is connected
to INT13 of the CPU. CPU-Timer 0 is also for general use, and is connected to the PIE block.
A
相关PDF资料
PDF描述
TMR320C2811ZHHQ CTV 21C 21#16 PIN RECP
TMR320C2811ZHHS TMS320R2811, TMS320R2812 Digital Signal Processors
TMR320C2812GHHA TMS320R2811, TMS320R2812 Digital Signal Processors
TMR320C2812GHHQ TMS320R2811, TMS320R2812 Digital Signal Processors
TMR320C2812GHHS TMS320R2811, TMS320R2812 Digital Signal Processors
相关代理商/技术参数
参数描述
TMR320C2811ZHHQ 制造商:TI 制造商全称:Texas Instruments 功能描述:TMS320R2811, TMS320R2812 Digital Signal Processors
TMR320C2811ZHHS 制造商:TI 制造商全称:Texas Instruments 功能描述:TMS320R2811, TMS320R2812 Digital Signal Processors
TMR320C2812GHHA 制造商:TI 制造商全称:Texas Instruments 功能描述:TMS320R2811, TMS320R2812 Digital Signal Processors
TMR320C2812GHHQ 制造商:TI 制造商全称:Texas Instruments 功能描述:TMS320R2811, TMS320R2812 Digital Signal Processors
TMR320C2812GHHS 制造商:TI 制造商全称:Texas Instruments 功能描述:TMS320R2811, TMS320R2812 Digital Signal Processors