- 您现在的位置：买卖IC网 > PDF目录19730 > TOP244GN (Power Integrations)IC OFFLINE SWIT OVP UVLO HV 8SMD PDF资料下载
参数资料
| 型号： | TOP244GN |
| 厂商： | Power Integrations |
| 文件页数： | 8/52页 |
| 文件大小： | 0K |
| 描述： | IC OFFLINE SWIT OVP UVLO HV 8SMD |
| 标准包装： | 50 |
| 系列： | TOPSwitch®-GX |
| 输出隔离： | 隔离 |
| 频率范围： | 66 ~ 132kHz |
| 输出电压： | 700V |
| 功率（瓦特）： | 28W |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 8-SMD（7 个接脚），鸥形翼 |
| 供应商设备封装： | SMD-8B |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
TOP242-250
required can be used to take advantage of the lower R DS(ON) for
higher ef?ciency/smaller heat sinking requirements. With
a second resistor connected between the EXTERNAL
CURRENT LIMIT (X) pin (Y, R or F package) or MULTI-
FUNCTION (M) pin (P or G package) and the recti?ed DC
high voltage bus, the current limit is reduced with increasing
line voltage, allowing a true power limiting operation against
line variation to be implemented. When using an RCD clamp,
this power limiting technique reduces maximum clamp
voltage at high line. This allows for higher re?ected voltage
designs as well as reducing clamp dissipation.
The leading edge blanking circuit inhibits the current limit
comparator for a short time after the output MOSFET is turned
on. The leading edge blanking time has been set so that, if a
power supply is designed properly, current spikes caused by
primary-side capacitances and secondary-side recti?er reverse
recovery time should not cause premature termination of the
switching pulse.
The current limit is lower for a short period after the leading
edge blanking time as shown in Figure 52. This is due to
dynamic characteristics of the MOSFET. To avoid triggering
the current limit in normal operation, the drain current waveform
should stay within the envelope shown.
Line Under-Voltage Detection (UV)
At power up, UV keeps TOPSwitch-GX off until the input line
voltage reaches the under-voltage threshold. At power down,
UV prevents auto-restart attempts after the output goes out
of regulation. This eliminates power down glitches caused
by slow discharge of the large input storage capacitor present
in applications such as standby supplies. A single resistor
connected from the LINE-SENSE pin (Y, R or F package) or
MULTI-FUNCTION pin (P or G package) to the recti?ed DC
high voltage bus sets UV threshold during power up. Once the
power supply is successfully turned on, the UV threshold is
lowered to 40% of the initial UV threshold to allow extended
input voltage operating range (UV low threshold). If the UV
low threshold is reached during operation without the power
supply losing regulation, the device will turn off and stay off
until UV (high threshold) has been reached again. If the power
supply loses regulation before reaching the UV low threshold,
the device will enter auto-restart. At the end of each auto-
restart cycle (S7), the UV comparator is enabled. If the UV
high threshold is not exceeded the MOSFET will be disabled
during the next cycle (see Figure 8). The UV feature can
be disabled independent of the OV feature as shown in
Figures 19 and 23.
Line Overvoltage Shutdown (OV)
The same resistor used for UV also sets an overvoltage threshold
which, once exceeded, will force TOPSwitch-GX output into
off-state. The ratio of OV and UV thresholds is preset at 4.5
as can be seen in Figure 11. When the MOSFET is off, the
recti?ed DC high voltage surge capability is increased to the
voltage rating of the MOSFET (700 V), due to the absence
of the re?ected voltage and leakage spikes on the drain. A
small amount of hysteresis is provided on the OV threshold to
prevent noise triggering. The OV feature can be disabled
independent of the UV feature as shown in Figures 18 and 32.
Line Feed-Forward with DC MAX Reduction
The same resistor used for UV and OV also implements line
voltage feed-forward, which minimizes output line ripple and
reduces power supply output sensitivity to line transients.
This feed-forward operation is illustrated in Figure 7 by the
different values of I L (Y, R or F package) or I M (P or G package).
Note that for the same CONTROL pin current, higher line
voltage results in smaller operating duty cycle. As an added
OSCILLATOR
(SAW)
DMAX
ENABLE FROM
X, L OR M PIN (STOP)
TIME
PI-2637-060600
Figure 10. Synchronization Timing Diagram.
8
O
11/05
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2586-2BM TR | IC CTRLR/SEQ HOT SWAP 14-SOIC |
| VE-24L-CY-F2 | CONVERTER MOD DC/DC 28V 50W |
| MIC2586-1BM TR | IC CTRLR/SEQ HOT SWAP 14-SOIC |
| MIC37150-3.3BR | IC REG LDO 3.3V 1.5A S-PAK-3 |
| VE-242-CY-F1 | CONVERTER MOD DC/DC 15V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TOP244GN- | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:TOPSwitch-GX Family Extended Power, Design Flexible, EcoSmart, Integrated Off-line Switcher |
| TOP244GN-TL | 功能描述:交流/直流开关转换器 20 W 85-265 VAC 28 W 230 VAC RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| TOP244G-TL | 功能描述:IC OFFLINE SWIT OVP UVLO HV 8SMD RoHS:否 类别:集成电路 (IC) >> PMIC - AC-DC 转换器，离线开关 系列:TOPSwitch®-GX 标准包装:1 系列:FPS™ 输出隔离:隔离 频率范围:61kHz ~ 73kHz 输入电压:8 V ~ 26 V 输出电压:650V 功率（瓦特）:12W 工作温度:-40°C ~ 115°C 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-MDIP 包装:Digi-Reel® 其它名称:FSL206MRBNFSDKR |
| TOP244P | 功能描述:IC OFFLINE SWIT OVP UVLO HV 8DIP RoHS:否 类别:集成电路 (IC) >> PMIC - AC-DC 转换器，离线开关 系列:TOPSwitch®-GX 标准包装:1 系列:FPS™ 输出隔离:隔离 频率范围:61kHz ~ 73kHz 输入电压:8 V ~ 26 V 输出电压:650V 功率（瓦特）:12W 工作温度:-40°C ~ 115°C 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-MDIP 包装:Digi-Reel® 其它名称:FSL206MRBNFSDKR |
| TOP244P- | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:TOPSwitch-GX Family Extended Power, Design Flexible, EcoSmart, Integrated Off-line Switcher |
发布紧急采购，3分钟左右您将得到回复。