参数资料
型号: TOP261YN
厂商: Power Integrations
文件页数: 21/50页
文件大小: 0K
描述: IC OFFLINE SWIT PROG OVP TO220
标准包装: 50
输出隔离: 隔离
频率范围: 119kHz ~ 145kHz
输出电压: 700V
功率(瓦特): 333W
工作温度: -40°C ~ 150°C
封装/外壳: TO-220-7(成形引线),6 引线
供应商设备封装: TO-220-7C
包装: 管件
产品目录页面: 1204 (CN2011-ZH PDF)
配用: 596-1193-ND - KIT REF DESIGN TOP HX FOR TOP258
其它名称: 596-1216-5
TOP252-262
Application Examples
A High Efficiency, 35 W, Dual Output - Universal Input
Power Supply
The circuit in Figure 41 takes advantage of several of the
TOPSwitch-HX features to reduce system cost and power
supply size and to improve efficiency. This design delivers
35 W total continuous output power from a 90 VAC to 265 VAC
input at an ambient of 50 oC in an open frame configuration. A
nominal efficiency of 84% at full load is achieved using
TOP258P. With a DIP-8 package, this design provides 35 W
continuous output power using only the copper area on the
circuit board underneath the part as a heat sink. The different
operating modes of the TOPSwitch-HX provide significant
improvement in the no-load, standby, and light load performance
of the power supply as compared to the previous generations of
the TOPSwitch.
Resistors R3 and R4 provide line sensing, setting line UV at
100 VDC and line OV at 450 VDC.
Diode D5, together with resistors R6, R7, capacitor C6 and TVS
VR1, forms a clamp network that limits the drain voltage of the
TOPSwitch after the integrated MOSFET turns off. TVS VR1
provides a defined maximum clamp voltage and typically only
conducts during fault conditions such as overload. This allows
the RCD clamp (R6, R7, C6 and D5) to be sized for normal
operation, thereby maximizing efficiency at light load. Should
the feedback circuit fail, the output of the power supply may
exceed regulation limits. This increased voltage at output will
also result in an increased voltage at the output of the bias
winding. Zener VR2 will break down and current will flow into
the “M” pin of the TOPSwitch initiating a hysteretic overvoltage
protection with automatic restart attempts. Resistor R5 will limit
the current into the M pin to < 336 m A, thus setting hysteretic
OVP. If latching OVP is desired, the value of R5 can be reduced
to 20 W .
The output voltage is controlled using the amplifier TL431.
Diode D9, capacitor C20 and resistor R16 form the soft finish
circuit. At startup, capacitor C20 is discharged. As the output
voltage starts rising, current flows through the optocoupler diode
inside U2A, resistor R13 and diode D9 to charge capacitor C20.
This provides feedback to the circuit on the primary side. The
current in the optocoupler diode U2A gradually decreases as the
capacitor C20 becomes charged and the control amplifier IC U3
becomes operational. This ensures that the output voltage
increases gradually and settles to the final value without any
overshoot. Resistor R16 ensures that the capacitor C20 is
maintained charged at all times after startup, which effectively
isolates C20 from the feedback circuit after startup. Capacitor
C20 discharges through R16 when the supply shuts down.
Resistors R20, R21 and R18 form a voltage divider network.
The output of this divider network is primarily dependent on the
divider circuit formed using R20 and R21 and will vary to some
extent for changes in voltage at the 15 V output due to the
connection of resistor R18 to the output of the divider network.
Resistor R19 and Zener VR3 improve cross regulation in case
only the 5 V output is loaded, which results in the 12 V output
operating at the higher end of the specification.
C6
3.9 nF
1 kV
C7
2.2 nF
250 VAC
R11
33 ?
C12
470 pF
100 V
D1
1N4937
D2
1N4007
R6
22 k ?
2W
T1
2 EER28 7
VR1
P6KE200A
3 11
C16
470 pF
100 V
D7
SB560
R12
33 ?
C13
680 μ F
25 V
C14
680 μ F
25 V
L2
3.3 μ H
L3
3.3 μ H
C15
220 μ F
25 V
C18
220 μ F
10 V
+12 V,
2A
RTN
+5 V,
2.2 A
D3
1N4937
D4
1N4007
R3
2.0 M ?
R7
20 ?
1/2 W
D5
FR106
4
9
6
D6 R10
FR106 4.7 ?
5
D8
SB530
C10
10 μ F
50 V
C17
2200 μ F
C11 10 V
2.2 nF
250 VAC
R19
10 ?
RTN
F1
3.15 A
M
6.8 ?
C9
47 μ F
L1
6.8 mH
R1 R2
1 M ? 1 M ?
C3
220 nF
275 VAC
RT1
L 10 ?
E
N
90 - 265
VAC
t
O
C4
100 μ F
400 V
R4
2.0 M ?
D
S
VR2
R5 1N5250B
5.1 k ? 20 V
TOPSwitch-HX
U1
CONTROL TOP258PN
C
R8
C8
100 nF
50 V
16 V
U2B
PS2501-
1-H-A
R16
10 k ?
C20
10 μ F
50 V
R13
330 ?
U2A
PS2501-
1-H-A
D9
1N4148
U3
TL431
2%
R14
22 ?
C19
1.0 μ F
50 V
R15
1 k ?
R17
10 k ?
VR3
BZX55B8V2
8.2 V
2%
R18
196 k ?
1%
C21
220 nF
50 V
R20
12.4 k ?
1%
R21
10 k ?
1%
PI-4747-020508
Figure 41. 35 W Dual Output Power Supply using TOP258PN.
21
www.powerint.com
Rev. H 06/13
相关PDF资料
PDF描述
EYM36DTBD-S273 CONN EDGECARD 72POS R/A .156 SLD
V150C8H100BL2 CONVERTER MOD DC/DC 8V 100W
TOP248YN IC OFFLINE SWIT UVLO HV TO220
MAX8891EXK33+T IC REG LDO 3.3V .15A SC70-5
TOP260YN IC OFFLINE SWIT PROG OVP TO220
相关代理商/技术参数
参数描述
TOP262EN 功能描述:交流/直流开关转换器 254W (85-264VAC) 333W (230V AC) RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压(最大值):23.5 V 输入/电源电压(最小值):11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel
TOP262EN6 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:Enhanced EcoSmart, Integrated Off-Line Switcher with Advanced Feature Set and Extended Power Range
TOP262LN 功能描述:交流/直流开关转换器 177W (85-264VAC) 244W (230V AC) RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压(最大值):23.5 V 输入/电源电压(最小值):11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel
TOP262LN6 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:Enhanced EcoSmart, Integrated Off-Line Switcher with Advanced Feature Set and Extended Power Range
TOP264 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:Integrated Off-Line Switcher with EcoSmart Technology for Highly Efficient Power Supplies