- 您现在的位置：买卖IC网 > PDF目录19879 > TOP261YN (Power Integrations)IC OFFLINE SWIT PROG OVP TO220 PDF资料下载
参数资料
| 型号： | TOP261YN |
| 厂商： | Power Integrations |
| 文件页数： | 22/50页 |
| 文件大小： | 0K |
| 描述： | IC OFFLINE SWIT PROG OVP TO220 |
| 标准包装： | 50 |
| 输出隔离： | 隔离 |
| 频率范围： | 119kHz ~ 145kHz |
| 输出电压： | 700V |
| 功率（瓦特）： | 333W |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | TO-220-7（成形引线），6 引线 |
| 供应商设备封装： | TO-220-7C |
| 包装： | 管件 |
| 产品目录页面： | 1204 (CN2011-ZH PDF) |
| 配用： | 596-1193-ND - KIT REF DESIGN TOP HX FOR TOP258 |
| 其它名称： | 596-1216-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
TOP252-262
A High Efficiency, 150 W, 250 – 380 VDC Input
Power Supply
The circuit shown in Figure 42 delivers 150 W (19 V @ 7.7 A) at
84% efficiency using a TOP258Y from a 250 VDC to 380 VDC
input. A DC input is shown, as typically at this power level a
power factor correction stage would precede this supply,
providing the DC input. Capacitor C1 provides local decoupling,
necessary when the supply is remote from the main PFC output
capacitor.
The flyback topology is still usable at this power level due to the
high output voltage, keeping the secondary peak currents low
enough so that the output diode and capacitors are reasonably
sized. In this example, the TOP258YN is at the upper limit of its
dissipated by VR1 and VR3, the leakage energy instead being
dissipated by R1 and R2. However, VR1 and VR3 are essential
to limit the peak drain voltage during start-up and/or overload
conditions to below the 700 V rating of the TOPSwitch-HX
MOSFET. The schematic shows an additional turn-off snubber
circuit consisting of R20, R21, R22, D5 and C18. This reduces
turn-off losses in the TOPSwitch-HX.
The secondary is rectified and smoothed by D2, D3 and C5,
C6, C7 and C8. Two windings are used and rectified with
separate diodes D2 and D3 to limit diode dissipation. Four
capacitors are used to ensure their maximum ripple current
specification is not exceeded. Inductor L1 and capacitors C15
and C16 provide switching noise filtering.
power capability.
Output voltage is controlled using a TL431 reference IC and
Resistors R3, R6 and R7 provide output power limiting,
maintaining relatively constant overload power with input voltage.
Line sensing is implemented by connecting a 4 M W resistor from
the V pin to the DC rail. Resistors R4 and R5 together form the
4 M W line sense resistor. If the DC input rail rises above
450 VDC, then TOPSwitch-HX will stop switching until the
voltage returns to normal, preventing device damage.
Due to the high primary current, a low leakage inductance
transformer is essential. Therefore, a sandwich winding with a
copper foil secondary was used. Even with this technique, the
leakage inductance energy is beyond the power capability of a
simple Zener clamp. Therefore, R1, R2 and C3 are added in
parallel to VR1 and VR3, two series TVS diodes being used to
reduce dissipation. During normal operation, very little power is
R15, R16 and R17 to form a potential divider to sense the
output voltage. Resistor R12 and R24 together limit the
optocoupler LED current and set overall control loop DC gain.
Control loop compensation is achieved using components C12,
C13, C20 and R13. Diode D6, resistor R23 and capacitor C19
form a soft finish network. This feeds current into the control
pin prior to output regulation, preventing output voltage
overshoot and ensuring startup under low line, full load
conditions.
Sufficient heat sinking is required to keep the TOPSwitch-HX
device below 110 ° C when operating under full load, low line
and maximum ambient temperature. Airflow may also be
required if a large heat sink area is not acceptable.
22 ?
0.5 W
250 - 380
VDC
F1
4A
RT1 O
5 ? t
R6
4.7 M ?
R4
2.0 M ?
R1 R2
68 k ? 68 k ?
2W 2W
C3
4.7 nF
1 kV
1
2.2 nF
250 VAC
C4
13,14
R14 C14
47 pF
1 kV
D2
MBR20100CT
C5-C8
820 μ F
25 V
L1
3.3 μ H
C15-C16
820 μ F
25 V
+19 V,
7.7 A
R7
4.7 M ?
R5
2.0 Μ?
D1
BYV26C
4
11
12
D3
MBR20100CT
RTN
VR1, VR3
P6KE100A
9,10
C1
22 μ F
400 V
R20
1.5 k ?
2W
T1
EI35
7
D4
1N4148
5
R18
22 ?
0.5 W
R8
4.7 ?
C17
47 pF
1 kV
R12
240 ?
0.125 W
C20
1.0 μ F
50 V
R21
1.5 k ?
2W
D5
1N4937
R19
4.7 ?
VR2
1N5258B
36 V
C9
10 μ F
50 V
R23
15 k ?
0.125 W
U2
PC817A
R24
30 ?
0.125 W
R16
31.6 k ?
1%
R3
8.06 k ?
1%
R22
1.5 k ?
2W
C18
120 pF
1 kV
D
S
V
CONTROL
X F
TOPSwitch-HX
U1
TOP258YN
C
C11
100 nF
50 V
R10
6.8 ?
C10
47 μ F
10 V
U2
PC817B
C19
10 μ F
50 V
D6
1N4148
R11
1 k ?
0.125 W
U3
TL431
2%
C12
4.7 nF
50 V
R13
56 k ?
0.125 W
R17
562 ?
1%
C13
100 nF
50 V
R15
4.75 k ?
1%
PI-4795-092007
Figure 42. 150 W, 19 V Power Supply using TOP258YN.
22
Rev. H 06/13
www.powerint.com
相关PDF资料 |
PDF描述 |
|---|---|
| EYM36DTBD-S273 | CONN EDGECARD 72POS R/A .156 SLD |
| V150C8H100BL2 | CONVERTER MOD DC/DC 8V 100W |
| TOP248YN | IC OFFLINE SWIT UVLO HV TO220 |
| MAX8891EXK33+T | IC REG LDO 3.3V .15A SC70-5 |
| TOP260YN | IC OFFLINE SWIT PROG OVP TO220 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TOP262EN | 功能描述:交流/直流开关转换器 254W (85-264VAC) 333W (230V AC) RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| TOP262EN6 | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:Enhanced EcoSmart, Integrated Off-Line Switcher with Advanced Feature Set and Extended Power Range |
| TOP262LN | 功能描述:交流/直流开关转换器 177W (85-264VAC) 244W (230V AC) RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| TOP262LN6 | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:Enhanced EcoSmart, Integrated Off-Line Switcher with Advanced Feature Set and Extended Power Range |
| TOP264 | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:Integrated Off-Line Switcher with EcoSmart Technology for Highly Efficient Power Supplies |
发布紧急采购，3分钟左右您将得到回复。