- 您现在的位置：买卖IC网 > PDF目录98268 > TPA0312PWPR (TEXAS INSTRUMENTS INC) 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 PDF资料下载
参数资料
| 型号： | TPA0312PWPR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频控制 |
| 英文描述： | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| 封装： | GREEN, PLASTIC, HTSSOP-24 |
| 文件页数： | 16/36页 |
| 文件大小： | 791K |
| 代理商： | TPA0312PWPR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
www.ti.com
RL
CC
VO(PP)
VDD
–3 dB
fc
SINGLE-ENDED OPERATION
BTL AMPLIFIER EFFICIENCY
V(LRMS)
VO
IDD
IDD(avg)
TPA0312
SLOS335A – DECEMBER 2000 – REVISED OCTOBER 2004
Figure 40. Single-Ended Configuration and Frequency Response
Increasing power to the load does carry a penalty of increased internal power dissipation. The increased
dissipation is understandable considering that the BTL configuration produces 4
× the output power of the SE
configuration. Internal dissipation versus output power is discussed further in the Crest Factor and Thermal
Considerations section.
In SE mode the load is driven from the primary amplifier output for each channel (OUT+, terminals 21 and 4).
The amplifier switches single-ended operation when the SE/BTL terminal is held high. This puts the negative
outputs in a high-impedance state, and reduces the amplifier's gain to 4.1 dB.
Class-AB amplifiers are notoriously inefficient. The primary cause of these inefficiencies is voltage drop across
the output stage transistors. There are two components of the internal voltage drop. One is the headroom or dc
voltage drop that varies inversely to output power. The second component is due to the sine-wave nature of the
output. The total voltage drop can be calculated by subtracting the RMS value of the output voltage from VDD.
The internal voltage drop multiplied by the RMS value of the supply current, IDDrms, determines the internal
power dissipation of the amplifier.
An easy-to-use equation to calculate efficiency starts out as being equal to the ratio of power from the power
supply to the power delivered to the load. To accurately calculate the RMS and average values of power in the
load and in the amplifier, the current and voltage waveform shapes must first be understood (see Figure 41).
Figure 41. Voltage and Current Waveforms for BTL Amplifiers
Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are
different between SE and BTL configurations. In an SE application, the current waveform is a half-wave rectified
shape, whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different.
Keep in mind that for most of the waveform both the push and pull transistors are not on at the same time, which
supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform.
The following equations are the basis for calculating amplifier efficiency.
23
相关PDF资料 |
PDF描述 |
|---|---|
| TPA0312PWP | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA0312PWPG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA0312PWPRG4 | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TPA032D02DCAR | 10 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO48 |
| TPA032D02DCA | 10 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPA0312PWPRG4 | 功能描述:音频放大器 St 2W Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA032D01 | 制造商:TI 制造商全称:Texas Instruments 功能描述:10-W MONO CLASS-D AUDIO POWER AMPLIFIER |
| TPA032D01_07 | 制造商:TI 制造商全称:Texas Instruments 功能描述:10-W MONO CLASS-D AUDIO POWER AMPLIFIER |
| TPA032D01DCA | 功能描述:音频放大器 10W Monaur RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA032D01DCA | 制造商:Texas Instruments 功能描述:IC SM POWER AMP CLASS-D AUDIO |
发布紧急采购，3分钟左右您将得到回复。