参数资料
型号: TPA2000D4DAPR
厂商: TEXAS INSTRUMENTS INC
元件分类: 音频/视频放大
英文描述: 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32
封装: PLASTIC, HTSSOP-32
文件页数: 11/27页
文件大小: 579K
代理商: TPA2000D4DAPR
TPA2000D4
STEREO 2W CLASSD AUDIO POWER AMPLIFIER
WITH STEREO HP AMPLIFIER
SLOS337B DECEMBER 2000 REVISED NOVEMBER 2005
19
WWW.TI.COM
APPLICATION INFORMATION
input capacitor, CI
In the typical application an input capacitor, CI, is required to allow the amplifier to bias the input signal to the
proper dc level for optimum operation. In this case, CI and the input impedance of the amplifier, ZI, form a
high-pass filter with the corner frequency determined in equation 5.
f
c(highpass) +
1
2
pZ
I
C
I
3 dB
fc
(5)
The value of CI is important as it directly affects the bass (low frequency) performance of the circuit. Consider
the example where ZI is 20 k and the specification calls for a flat bass response down to 80 Hz. Equation 5
is reconfigured as equation 6.
C
I +
1
2
pZ
I fc
(6)
In this example, CI is 0.1 F, so one would likely choose a value in the range of 0.1 F to 1 F. If the gain is known
and is constant, use ZI from Table 1 to calculate CI. A further consideration for this capacitor is the leakage path
from the input source through the input network (CI) and the feedback network to the load. This leakage current
creates a dc offset voltage at the input to the amplifier that reduces useful headroom, especially in high gain
applications. For this reason a low-leakage tantalum or ceramic capacitor is the best choice. When polarized
capacitors are used, the positive side of the capacitor should face the amplifier input in most applications as
the dc level there is held at VDD/2, which is likely higher than the source dc level. Note that it is important to
confirm the capacitor polarity in the application.
CI must be 10 times smaller than the bypass capacitor to reduce clicking and popping noise from power on/off
and entering and leaving shutdown. After sizing CI for a given cutoff frequency, size the bypass capacitor to 10
times that of the input capacitor.
(7)
CI ≤ CBYP / 10
switching frequency
The switching frequency is determined using the values of the components connected to ROSC (pin 18) and
COSC (pin 19) and is calculated with the following equation:
fs +
6.6
R
OSC
C
OSC
(8)
The switching frequency was chosen to be centered on 250 kHz. This frequency represents the optimization
of audio fidelity due to oversampling and the maximization of efficiency by minimizing the switching losses of
the amplifier. The recommended values are a resistance of 120 k
and a capacitance of 220 pF. Using these
component values, the amplifier operates properly by using 5% tolerance resistors and 10% tolerance
capacitors. The tolerance of the components can be changed, as long as the switching frequency remains
between 200 kHz and 300 kHz. Within this range, the internal circuitry of the device provides stable operation.
相关PDF资料
PDF描述
TPA2000D4DAP 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32
TPA2000D4DAPG4 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32
TPA2000D4GQC 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA32
TPA2001D1GQCR 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA48
TPA2001D1GQC 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA48
相关代理商/技术参数
参数描述
TPA2000D4DAPRG4 功能描述:音频放大器 Stereo Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TPA2000D4EVM 功能描述:音频 IC 开发工具 TPA2000D4 Eval Mod RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V
TPA2000D4GQC 制造商:未知厂家 制造商全称:未知厂家 功能描述:AUDIO AMPLIFIER|DUAL|CMOS|BGA|48PIN|PLASTIC
TPA2001D1 制造商:TI 制造商全称:Texas Instruments 功能描述:1-W FILTERLESS MONO CLASS-D AUDIO POWER AMPLIFIER
TPA2001D1_06 制造商:TI 制造商全称:Texas Instruments 功能描述:1-W FILTERLESS MONO CLASS-D AUDIO POWER AMPLIFIER