- 您现在的位置：买卖IC网 > PDF目录98269 > TPA2000D4DAPR (TEXAS INSTRUMENTS INC) 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 PDF资料下载
参数资料
| 型号： | TPA2000D4DAPR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| 封装： | PLASTIC, HTSSOP-32 |
| 文件页数： | 13/27页 |
| 文件大小： | 579K |
| 代理商： | TPA2000D4DAPR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
TPA2000D4
STEREO 2W CLASSD AUDIO POWER AMPLIFIER
WITH STEREO HP AMPLIFIER
SLOS337B DECEMBER 2000 REVISED NOVEMBER 2005
20
WWW.TI.COM
APPLICATION INFORMATION
gain setting resistors, RF and RI for HP amplifier
The voltage gain for the TPA2000D4 headphone amplifier is set by resistors RF and RI according to equation 9.
(9)
Gain
+*
R
F
R
I
or Gain (dB)
+ 20 log
R
F
R
I
Given that the TPA2000D4 is a MOS amplifier, the input impedance is very high. Consequently input leakage
currents are not generally a concern, although noise in the circuit increases as the value of RF increases. In
addition, a certain range of RF values is required for proper start-up operation of the amplifier. Taken together
it is recommended that the effective impedance seen by the inverting node of the amplifier be set between
5 k
and 20 k. The effective impedance is calculated in equation 10.
(10)
Effective Impedance
+
R
FRI
R
F ) RI
As an example, consider an input resistance of 20 k
and a feedback resistor of 20 k. The gain of the amplifier
would be 1 and the effective impedance at the inverting terminal would be 10 k
, which is within the
recommended range.
For high performance applications, metal film resistors are recommended because they tend to have lower
noise levels than carbon resistors. For values of RF above 50 k, the amplifier tends to become unstable due
to a pole formed from RF and the inherent input capacitance of the MOS input structure. For this reason, a small
compensation capacitor of approximately 5 pF should be placed in parallel with RF. This, in effect, creates a
low-pass filter network with the cutoff frequency defined in equation 11.
(11)
fc +
1
2
pR
F CF
For example, if RF is 100 k and CF is 5 pF then fc is 318 kHz, which is well outside the audio range.
For maximum signal swing and output power at low supply voltages like 1.6 V to 3.3 V, BYPASS is biased to
VDD/4. However, to allow the output to be biased at VDD/2, a resistor, R, equal to RF must be placed from the
negative input to ground.
input capacitor, CI for HP amplifier
In the typical application, an input capacitor, CI, is required to allow the amplifier to bias the input signal to the
proper dc level for optimum operation. In this case, CI and RI form a high-pass filter with the corner frequency
determined in equation 12.
(12)
fc +
1
2
pR
I
C
I
The value of CI is important to consider, as it directly affects the bass (low frequency) performance of the circuit.
Consider the example where RI is 20 k and the specification calls for a flat bass response down to 20 Hz.
Equation 4 is reconfigured as equation 13.
(13)
C
I +
1
2
pR
I fc
In this example, CI is 0.40 F, so one would likely choose a value in the range of 0.47 F to 1 F. A further
consideration for this capacitor is the leakage path from the input source through the input network (RI, CI) and
the feedback resistor (RF) to the load. This leakage current creates a dc offset voltage at the input to the amplifier
that reduces useful headroom, especially in high-gain applications (>10). For this reason a low-leakage
tantalum or ceramic capacitor is the best choice. When polarized capacitors are used, the positive side of the
capacitor should face the amplifier input in most applications, as the dc level there is held at VDD/4, which is
likely higher than the source dc level. It is important to confirm the capacitor polarity in the application.
相关PDF资料 |
PDF描述 |
|---|---|
| TPA2000D4DAP | 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| TPA2000D4DAPG4 | 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| TPA2000D4GQC | 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA32 |
| TPA2001D1GQCR | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA48 |
| TPA2001D1GQC | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPA2000D4DAPRG4 | 功能描述:音频放大器 Stereo Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA2000D4EVM | 功能描述:音频 IC 开发工具 TPA2000D4 Eval Mod RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| TPA2000D4GQC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:AUDIO AMPLIFIER|DUAL|CMOS|BGA|48PIN|PLASTIC |
| TPA2001D1 | 制造商:TI 制造商全称:Texas Instruments 功能描述:1-W FILTERLESS MONO CLASS-D AUDIO POWER AMPLIFIER |
| TPA2001D1_06 | 制造商:TI 制造商全称:Texas Instruments 功能描述:1-W FILTERLESS MONO CLASS-D AUDIO POWER AMPLIFIER |
发布紧急采购，3分钟左右您将得到回复。