- 您现在的位置：买卖IC网 > PDF目录98271 > TPA2016D2RTJT (TEXAS INSTRUMENTS INC) 2.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC20 PDF资料下载
参数资料
| 型号： | TPA2016D2RTJT |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 2.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC20 |
| 封装： | 4 X 4 MM, GREEN, PLASTIC, QFN-20 |
| 文件页数： | 21/38页 |
| 文件大小： | 1216K |
| 代理商： | TPA2016D2RTJT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
COMPONENT LOCATION
TRACE WIDTH
SLOS524D – JUNE 2008 – REVISED AUGUST 2009........................................................................................................................................................ www.ti.com
Figure 41. Land Pattern Dimensions
Table 5. Land Pattern Dimensions(1) (2) (3) (4)
SOLDER PAD
SOLDER MASK(5)
COPPER
STENCIL
COPPER PAD
STENCIL(6) (7) OPENING
DEFINITIONS
OPENING
THICKNESS
275
m
375
m
Non solder mask
275
m × 275 m Sq. (rounded
1 oz max (32
m)
125
m thick
defined (NSMD)
corners)
(+0.0, –25
m)
(+0.0, –25
m)
(1)
Circuit traces from NSMD defined PWB lands should be 75
m to 100 m wide in the exposed area inside the solder mask opening.
Wider trace widths reduce device stand off and impact reliability.
(2)
Best reliability results are achieved when the PWB laminate glass transition temperature is above the operating the range of the
intended application.
(3)
Recommend solder paste is Type 3 or Type 4.
(4)
For a PWB using a Ni/Au surface finish, the gold thickness should be less 0.5 mm to avoid a reduction in thermal fatigue performance.
(5)
Solder mask thickness should be less than 20
m on top of the copper circuit pattern
(6)
Best solder stencil performance is achieved using laser cut stencils with electro polishing. Use of chemically etched stencils results in
inferior solder paste volume control.
(7)
Trace routing away from WCSP device should be balanced in X and Y directions to avoid unintentional component movement due to
solder wetting forces.
Place all the external components very close to the TPA2016D2. Placing the decoupling capacitor, CS, close to
the TPA2016D2 is important for the efficiency of the Class-D amplifier. Any resistance or inductance in the trace
between the device and the capacitor can cause a loss in efficiency.
Recommended trace width at the solder balls is 75
m to 100 m to prevent solder wicking onto wider PCB
traces. For high current pins (PVDD (L, R), PGND, and audio output pins) of the TPA2016D2, use 100-
m trace
widths at the solder balls and at least 500-
m PCB traces to ensure proper performance and output power for
the device. For the remaining signals of the TPA2016D2, use 75-
m to 100-m trace widths at the solder balls.
The audio input pins (INR± and INL±) must run side-by-side to maximize common-mode noise cancellation
28
Copyright 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): TPA2016D2
相关PDF资料 |
PDF描述 |
|---|---|
| TPA2017D2RTJR | 2.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC20 |
| TPA2017D2RTJT | 2.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC20 |
| TPA2026D2YZHR | AUDIO AMPLIFIER, PBGA16 |
| TPA2026D2YZHT | AUDIO AMPLIFIER, PBGA16 |
| TPA2028D1YZFR | 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPA2016D2V1YZHR | 制造商:Texas Instruments 功能描述: |
| TPA2016D2YZHR | 功能描述:音频放大器 1.7W/Ch Stereo Class D Aud Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA2016D2YZHT | 功能描述:音频放大器 1.7W/Ch Stereo Class D Aud Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA2016DYZHT2 | 制造商:Texas Instruments 功能描述: |
| TPA2017D2 | 制造商:TI 制造商全称:Texas Instruments 功能描述:2.8-W/Ch Stereo Class-D Audio Amplifier with SmartGainTM Dynamic Range Compression and AGC |
发布紧急采购，3分钟左右您将得到回复。