- 您现在的位置：买卖IC网 > PDF目录98272 > TPA3100D2PHPR (TEXAS INSTRUMENTS INC) 21.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 PDF资料下载
参数资料
| 型号： | TPA3100D2PHPR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 21.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| 封装： | 9 X 9 MM, GREEN, PLASTIC, HTQFP-48 |
| 文件页数： | 17/41页 |
| 文件大小： | 1191K |
| 代理商： | TPA3100D2PHPR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
F
=
OSC
1
2xROSCxCOSC
SLOS469F – OCTOBER 2005 – REVISED AUGUST 2010
www.ti.com
A secondary function of the VBYP capacitor is to filter high-frequency noise on the internal 1.25-V bias generator.
A value of at least 0.47F is recommended for the VBYP capacitor. For the best power-up and shutdown pop
performance, the VBYP capacitor should be greater than or equal to the input capacitors.
ROSC Resistor Selection
The resistor connected to the ROSC terminal controls the class-D output switching frequency using Equation 4:
(4)
COSC is an internal capacitor that is nominally equal to 20 pF. Variation over process and temperature can
result in a ±15% change in this capacitor value.
For example, if ROSC is fixed at 100 k
, the frequency from device to device with this fixed resistance could
vary from 217 kHz to 294 kHz with a 15% variation in the internal COSC capacitor. The tolerance of the ROSC
resistor should also be considered to determine the range of expected switching frequencies from device to
device. It is recommended that 1% tolerance resistors be used.
Differential Input
The differential input stage of the amplifier cancels any noise that appears on both input lines of the channel. To
use the TPA3100D2 with a differential source, connect the positive lead of the audio source to the INP input and
the negative lead from the audio source to the INN input. To use the TPA3100D2 with a single-ended source, ac
ground the INP or INN input through a capacitor equal in value to the input capacitor on INN or INP and apply
the audio source to either input. In a single-ended input application, the unused input should be ac grounded at
the audio source instead of at the device input for best noise performance.
SHUTDOWN OPERATION
The TPA3100D2 employs a shutdown mode of operation designed to reduce supply current (ICC) to the absolute
minimum level during periods of nonuse for power conservation. The SHUTDOWN input terminal should be held
high (see specification table for trip point) during normal operation when the amplifier is in use. Pulling
SHUTDOWN low causes the outputs to mute and the amplifier to enter a low-current state. Never leave
SHUTDOWN unconnected, because amplifier operation would be unpredictable.
For the best power-off pop performance, place the amplifier in the shutdown or mute mode prior to removing the
power supply voltage.
MUTE Operation
The MUTE pin is an input for controlling the output state of the TPA3100D2. A logic high on this terminal
disables the outputs. A logic low on this pin enables the outputs. This terminal may be used as a quick
disable/enable of outputs when changing channels on a television or transitioning between different audio
sources.
The MUTE terminal should never be left floating. For power conservation, the SHUTDOWN terminal should be
used to reduce the quiescent current to the absolute minimum level.
The MUTE terminal can also be used with the FAULT output to automatically recover from a short-circuit event.
When a short-circuit event occurs, the FAULT terminal transitions high indicating a short-circuit has been
detected. When directly connected to MUTE, the MUTE terminal transitions high, and clears the internal fault
flag. This causes the FAULT terminal to cycle low, and normal device operation resumes if the short-circuit is
removed from the output. If a short remains at the output, the cycle continues until the short is removed.
If external MUTE control is desired, and automatic recovery from a short-circuit event is also desired, an OR gate
can be used to combine the functionality of the FAULT output and external MUTE control, see Figure 34.
24
Copyright 2005–2010, Texas Instruments Incorporated
Product Folder Link(s): TPA3100D2
相关PDF资料 |
PDF描述 |
|---|---|
| TPA3100D2RGZRG4 | 21.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC48 |
| TPA3100D2RGZTG4 | 21.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC48 |
| TPA3101D2RGZRG4 | 10 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC48 |
| TPA3101D2RGZR | 10 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC48 |
| TPA3101D2RGZTG4 | 10 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPA3100D2PHPRG4 | 功能描述:音频放大器 20 W Stereo Class-D Audio Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA3100D2-Q1 | 制造商:TI 制造商全称:Texas Instruments 功能描述:20-W STEREO CLASS-D AUDIO POWER AMPLIFIER |
| TPA3100D2RGZR | 功能描述:音频放大器 20 W Stereo Class-D Audio Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA3100D2RGZRG4 | 功能描述:音频放大器 20 W Stereo Class-D Audio Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA3100D2RGZR-P | 制造商:TI 制造商全称:Texas Instruments 功能描述:20-W STEREO CLASS-D AUDIO POWER AMPLIFIER |
发布紧急采购，3分钟左右您将得到回复。