参数资料
型号: TPA3101D2PHP
厂商: TEXAS INSTRUMENTS INC
元件分类: 音频/视频放大
英文描述: 10 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48
封装: 7 X 7 MM, GREEN, PLASTIC, HTQFP-48
文件页数: 21/41页
文件大小: 1073K
代理商: TPA3101D2PHP
SLOS473C – DECEMBER 2005 – REVISED SEPTEMBER 2007
www.ti.com
BASIC MEASUREMENT SYSTEM
This application note focuses on methods that use the basic equipment listed below:
Audio analyzer or spectrum analyzer
Digital multimeter (DMM)
Oscilloscope
Twisted-pair wires
Signal generator
Power resistor(s)
Linear regulated power supply
Filter components
EVM or other complete audio circuit
Figure 35 shows the block diagrams of basic measurement systems for class-AB and class-D amplifiers. A sine
wave is normally used as the input signal because it consists of the fundamental frequency only (no other
harmonics are present). An analyzer is then connected to the APA output to measure the voltage output. The
analyzer must be capable of measuring the entire audio bandwidth. A regulated dc power supply is used to
reduce the noise and distortion injected into the APA through the power pins. A System Two audio measurement
system (AP-II) (Reference 1) by Audio Precision includes the signal generator and analyzer in one package.
The generator output and amplifier input must be ac-coupled. However, the EVMs already have the ac-coupling
capacitors, (CIN), so no additional coupling is required. The generator output impedance should be low to avoid
attenuating the test signal, and is important because the input resistance of APAs is not high. Conversely, the
analyzer-input impedance should be high. The output resistance, ROUT, of the APA is normally in the hundreds of
milliohms and can be ignored for all but the power-related calculations.
Figure 35(a) shows a class-AB amplifier system. It takes an analog signal input and produces an analog signal
output. This amplifier circuit can be directly connected to the AP-II or other analyzer input.
This is not true of the class-D amplifier system shown in Figure 35(b), which requires low-pass filters in most
cases in order to measure the audio output waveforms. This is because it takes an analog input signal and
converts it into a pulse-width modulated (PWM) output signal that is not accurately processed by some
analyzers.
28
Copyright 2005–2007, Texas Instruments Incorporated
Product Folder Link(s): TPA3101D2
相关PDF资料
PDF描述
TPA3101D2PHPG4 10 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48
TPA3101D2PHPRG4 10 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48
TPA3106D1VFPG4 40 W, 1 CHANNEL, AUDIO AMPLIFIER, PQFP32
TPA3106D1VFPRG4 40 W, 1 CHANNEL, AUDIO AMPLIFIER, PQFP32
TPA3106D1VFPR 40 W, 1 CHANNEL, AUDIO AMPLIFIER, PQFP32
相关代理商/技术参数
参数描述
TPA3101D2PHP 制造商:Texas Instruments 功能描述:IC AMP AUDIO PWR 10W STER 48TQFP 制造商:Texas Instruments 功能描述:IC, AMP AUDIO PWR 10W STER 48TQFP
TPA3101D2PHPG4 功能描述:音频放大器 10-W Stereo Class-D Aud Power Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TPA3101D2PHPR 功能描述:音频放大器 10-W Stereo Class-D Aud Power Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TPA3101D2PHPRG4 功能描述:音频放大器 10-W Stereo Class-D Aud Power Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TPA3101D2RGZR 功能描述:音频放大器 10-W Stereo Class-D Aud Power Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel