- 您现在的位置：买卖IC网 > PDF目录98279 > TPS2300IPWRG4 (TEXAS INSTRUMENTS INC) 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 PDF资料下载
参数资料
| 型号： | TPS2300IPWRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| 封装： | GREEN, PLASTIC, TSSOP-20 |
| 文件页数： | 9/24页 |
| 文件大小： | 643K |
| 代理商： | TPS2300IPWRG4 |
www.ti.com
SETTING THE CURRENT-LIMIT CIRCUIT-BREAKER THRESHOLD
I
LMT1 +
R
ISET1
50
10–6
R
ISENSE1
(2)
SETTING THE POWER-GOOD THRESHOLD VOLTAGE
R
VSENSE1_TOP +
V
O1_min * 1.225
1.225
R
VSENSE1_BOT
(3)
UNDERVOLTAGE LOCKOUT (UVLO)
SLVS265G – FEBRUARY 2000 – REVISED NOVEMBER 2006
During an overcurrent fault condition, the external MOSFET transistor that exhibited an overcurrent condition
is rapidly turned off by an internal pulldown circuit capable of pulling in excess of 400 mA (at 4 V) from the
pin. Once the gate has been pulled below approximately 1.5 V, this driver is disengaged and the UVLO
driver is enabled instead. If one channel experiences an overcurrent condition and the other does not, then
only the channel that is conducting excessive current is turned off rapidly. The other channel continues to
operate normally.
Using channel 1 as an example, the current sensing resistor RISENSE1 and the current limit setting resistor RISET1
determine the current limit of the channel, and can be calculated by the following equation:
Typically RISENSE1 is usually very small (0.001 to 0.1). If the trace and solder-junction resistances between the
junction of RISENSE1 and ISENSE1 and the junction of RISENSE1 and RISET1 are greater than 10% of the RISENSE1
value, then these resistance values should be added to the RISENSE1 value used in the calculation above.
The above information and calculation also apply to channel 2. Table 4 shows some of the current sense
resistors available in the market.
Table 4. Some Current Sense Resistors
CURRENT RANGE
PART NUMBER
DESCRIPTION
MANUFACTURER
(A)
0 to 1
WSL-1206, 0.05 1%
0.05
, 0.25 W, 1% resistor
1 to 2
WSL-1206, 0.025 1%
0.025
, 0.25 W, 1% resistor
2 to 4
WSL-1206, 0.015 1%
0.015
, 0.25 W, 1% resistor
Vishay Dale
4 to 6
WSL-2010, 0.010 1%
0.010
, 0.5 W, 1% resistor
6 to 8
WSL-2010, 0.007 1%
0.007
, 0.5 W, 1% resistor
8 to 10
WSR-2, 0.005 1%
0.005
, 0.5 W, 1% resistor
The two feedback resistors RVSENSEx_TOP and RVSENSEx_BOT connected between VOx and ground form a resistor
divider setting the voltage at the VSENSEx pins. VSENSE1 voltage equals:
VI(SENSE1) = VO× RVSENSE1_BOT/(RVSENSE1_TOP + RVSENSE1_BOT)
This voltage is compared to an internal voltage reference (1.225 V
±2%) to determine whether the output voltage
level is within a specified tolerance. For example, given a nominal output voltage at VO1, and defining VO1_min as
the minimum required output voltage, then the feedback resistors are defined by:
Start the process by selecting a large standard resistor value for RVSENSE1_BOT to reduce power loss. Then
RVSENSE1_TOP can be calculated by inserting all of the known values into the equation above. When VO1 is lower
than VO1_min, PWRGD1 is low as long as the controller is enabled.
The TPS2300/01 includes an undervoltage lockout (UVLO) feature that monitors the voltage present on the
VREG pin. This feature disables both external MOSFETs if the voltage on VREG drops below 2.78 V (nominal)
and re-enables normal operation when it rises above 2.85 V (nominal). Since VREG is fed from IN1 through a
low-dropout voltage regulator, the voltage on VREG tracks the voltage on IN1 within 50 mV. While the
undervoltage lockout is engaged, both GATE1 and GATE2 are held low by internal PMOS pulldown transistors,
ensuring that the external MOSFET transistors remain off at all times, even if all power supplies have fallen to
0V.
17
相关PDF资料 |
PDF描述 |
|---|---|
| TPS2306DWG4 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| TPS2340APFPRG4 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP80 |
| TPS2341PHPR | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48 |
| TPS2343DDPG3 | 6-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO80 |
| TPS2343DDPR | 6-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS2301EVM-153 | 功能描述:电源管理IC开发工具 TPS23XX Hot Swap Pow Contrs Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS2301IPW | 功能描述:热插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2301IPWG4 | 功能描述:热插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2301IPWR | 功能描述:热插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2301IPWRG4 | 功能描述:热插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。