- 您现在的位置：买卖IC网 > PDF目录68612 > TPS2398DGKRG4 (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF资料下载
参数资料
| 型号： | TPS2398DGKRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封装： | GREEN, PLASTIC, MSOP-8 |
| 文件页数： | 23/27页 |
| 文件大小： | 792K |
| 代理商： | TPS2398DGKRG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页
TPS2398
TPS2399
SLUS562A JUNE 2003 REVISED SEPTEMBER 2003
5
www.ti.com
DETAILED PIN DESCRIPTIONS
EN: Enable input to turn on/off power to the load. The EN pin is referenced to the VIN potential of the circuit.
When this input is pulled high (above the nominal 1.4-V threshold) the device enables the GATE output, and
begins the ramp of current to the load. When this input is low, the linear current amplifier (LCA) is disabled, and
a large pull-down device is applied to the FET gate, disabling power to the load.
FLTTIME: Connection for user-programming of the fault timeout period. An external capacitor connected from
FLTTIME to VIN establishes the timeout period to declare a fault condition. This timeout protects against
indefinite current sourcing into a faulted load, and also provides a filter against nuisance trips from momentary
current spikes or surges. The TPS2398 and TPS2399 define a fault condition as voltage at the ISENS pin at
or greater than the 40-mV fault threshold. When a fault condition exists, the timer is active. The devices manage
fault timing by charging the external capacitor to the 4-V fault threshold, then subsequently discharging it to reset
the timer (TPS2398), or discharging it at approximately 1% the charge rate to establish the duty cycle for retrying
the load (TPS2399). Whenever the internal fault latch is set (timer expired), the pass FET is rapidly turned off,
and the PG output is deasserted.
GATE: Gate drive for external N-channel FET. When enabled, and the input supply is above the UVLO
threshold, the gate drive is enabled and the device begins charging an external capacitor connected to the
IRAMP pin. This pin voltage is used to develop the reference voltage at the non-inverting input of the internal
LCA. The inverting input is connected to the current sense node, ISENS. The LCA acts to slew the pass FET
gate to force the ISENS voltage to track the reference. The reference is internally clamped at 40 mV, so the
maximum current that can be sourced to the load is determined by the sense resistor value as IMAX
≤ 40
mV/RSENSE. Once the load voltage has ramped up to the input dc potential, and current demand drops off, the
LCA drives the GATE output to about 14 V to fully enhance the pass FET, completing the low-impedance supply
return path for the load.
IRAMP: Programming input for setting the inrush current slew rate. An external capacitor connected between
this pin and VIN establishes the load current slew rate whenever power to the load is enabled. The device
charges the external capacitor to establish the reference input to the LCA. The closed-loop control of the LCA
and pass FET acts to maintain the current sense voltage at ISENS at the reference potential. Since the sense
voltage is developed as the drop across a resistor, the charging current ramp rate is set by the voltage ramp
rate at the IRAMP pin. When the output is disabled via the EN input or due to a load fault, the capacitor is
discharged and held low to initialize for the next turn-on.
ISENS: Current sense input. An external low value resistor connected between this pin and VIN is used to feed
back current magnitude information to the TPS2398/99. There are two internal device thresholds associated
with the voltage at the ISENS pin. During charging of the load’s input capacitance, or during other periods of
excessive demand, the HSPM acts to limit this voltage to 40 mV. Whenever the LCA is in current regulation
mode, the capacitor at FLTTIME is charged to activate the timer. If, when the LCA is driving to its supply rail,
a fast-acting fault such as a short-circuit, causes the ISENS voltage to exceed 100 mV (the overload threshold),
the GATE pin is pulled low rapidly, bypassing the fault timer.
PG: Open-drain, active-low indication of load power good. A power good status is declared when the output
is enabled, the GATE pin voltage has ramped to at least 7 V, and the voltage on the IRAMP pin exceeds
approximately 5 V. This last condition assures that full programmed sourcing current is available prior to
declaring power good, even with very slow current ramp rates. This additional protection prevents potential
discharging of the module input bulk capacitance during load turn-on.
RTN: Positive supply input for the TPS2398/99. For negative voltage systems, the supply pin connects directly
to the return node of the input power bus. Internal regulators step down the input voltage to generate the various
supply levels used by the TPS2398 and TPS2399.
VIN: Negative supply input and reference pin for the TPS2398/99. This pin connects directly to the input supply
negative rail. The input and output pins and all internal circuitry are referenced to this pin, so it is essentially the
GND or VSS pin of the device.
相关PDF资料 |
PDF描述 |
|---|---|
| TPS3802L30DCK | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3801T50DCKT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3801E18DCK | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3801-01DCKRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3802L30DCKRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS2398EVM | 功能描述:电源管理IC开发工具 TPS2398 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS2399D | 制造商:Texas Instruments 功能描述: |
| TPS2399DGK | 功能描述:热插拔功率分布 Simple -48V Controller w/Enable RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2399DGKG4 | 功能描述:热插拔功率分布 Simple -48V Controller w/Enable RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2399DGKR | 功能描述:热插拔功率分布 Simple -48V Controller w/Enable RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。