- 您现在的位置：买卖IC网 > PDF目录68612 > TPS2398DGKRG4 (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF资料下载
参数资料
| 型号： | TPS2398DGKRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封装： | GREEN, PLASTIC, MSOP-8 |
| 文件页数： | 4/27页 |
| 文件大小： | 792K |
| 代理商： | TPS2398DGKRG4 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
TPS2398
TPS2399
SLUS562A JUNE 2003 REVISED SEPTEMBER 2003
12
www.ti.com
APPLICATION INFORMATION
RAMPHI
1
7
6
3
4
2
8
5
IRAMP
EN
RTN
VIN
GATE
ISENS
FLTTIME
+
1.4 V
600 nA
SLOW
99 R
R
40 mV
ENA
+
30 V
EN_AMP
+
LCA
VDD
OC
+
100 mV
+
LATCH/
LOGIC
QS
RST
+
ENA
RTRY
4 V
0.5 V
TIMER BLOCK
DCHG
TPS2399 ONLY
OL
OVERLOAD
COMPARATOR
SQ
Q
R
GATEHI
ENA
FLT
OC
UDG03068
10
A
50
A
0.4
A
VDD
Ramp Control
14 V
FLT
PG
ON
Figure 19. Block Diagram
Fault timing is accomplished by connecting a capacitor between the FLTTIME and VIN pins, allowing
user-programming of the timeout period. Whenever the hot swap controller is in current control mode as
described above, the LCA asserts an overcurrent indication (OC in the Figure 17 diagram). Overcurrent fault
timing is inhibited during the slow turn-on portion of the IRAMP waveform. However, once the device transitions
to the normal rate current ramp (VO(IRAMP) ≥ 0.5 V), the external capacitor is charged by a 50-A source,
generating a voltage ramp at the FLTTIME pin. If the load voltage ramps successfully, the fault capacitor is
discharged (DCHG signal), and load initialization can begin. However, if the timing capacitor voltage attains the
4-V fault threshold, the LCA is disabled, the pass FET is rapidly turned off, and the fault is latched. Fault capacitor
charging ceases, and the capacitor is then discharged. In addition, latching of a fault condition causes rapid
discharge of the IRAMP capacitor. In this manner, the soft-start function is then reset and ready for the next
output enable, if and when conditions permit.
相关PDF资料 |
PDF描述 |
|---|---|
| TPS3802L30DCK | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3801T50DCKT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3801E18DCK | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3801-01DCKRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3802L30DCKRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS2398EVM | 功能描述:电源管理IC开发工具 TPS2398 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS2399D | 制造商:Texas Instruments 功能描述: |
| TPS2399DGK | 功能描述:热插拔功率分布 Simple -48V Controller w/Enable RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2399DGKG4 | 功能描述:热插拔功率分布 Simple -48V Controller w/Enable RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2399DGKR | 功能描述:热插拔功率分布 Simple -48V Controller w/Enable RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。