参数资料
型号: TPS40052PWP
厂商: TEXAS INSTRUMENTS INC
元件分类: 稳压器
英文描述: SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
封装: GREEN, PLASTIC, HTSSOP-16
文件页数: 13/33页
文件大小: 753K
代理商: TPS40052PWP
TPS40052
SLUS563C AUGUST 2003 REVISED FEBRUARY 2005
20
www.ti.com
LAYOUT CONSIDERATIONS
The PowerPAD
t package
The PowerPAD package provides low thermal impedance for heat removal from the device. The PowerPAD
derives its name and low thermal impedance from the large bonding pad on the bottom of the device. For
maximum thermal performance, the circuit board must have an area of solder-tinned-copper underneath the
package. The dimensions of this area depends on the size of the PowerPAD package. For a 16-pin TSSOP
(PWP) package the area is 5 mm x 3.4 mm [3].
Thermal vias connect this area to internal or external copper planes and should have a drill diameter sufficiently
small so that the via hole is effectively plugged when the barrel of the via is plated with copper. This plug is
needed to prevent wicking the solder away from the interface between the package body and the solder-tinned
area under the device during solder reflow. Drill diameters of 0.33 mm (13 mils) works well when 1-oz copper
is plated at the surface of the board while simultaneously plating the barrel of the via. If the thermal vias are not
plugged when the copper plating is performed, then a solder mask material should be used to cap the vias with
a diameter equal to the via diameter of 0.1 mm minimum. This capping prevents the solder from being wicked
through the thermal vias and potentially creating a solder void under the package. Refer to PowerPAD Thermally
Enhanced Package[3] and the mechanical illustration at the end of this document for more information on the
PowerPAD package.
Thermal Pad
6,60 mm
6,20 mm
4,50 mm
4,30 mm
10
1
X: Minimum PowerPAD = 1.8 mm
X
Y: Minimum PowerPAD = 1.4 mm
Y
Figure 9. PowerPAD Dimensions
MOSFET Packaging
MOSFET package selection depends on MOSFET power dissipation and the projected operating conditions.
In general, for a surface-mount applications, the DPAK style package provides the lowest thermal impedance
(
θJA) and, therefore, the highest power dissipation capability. However, the effectiveness of the DPAK depends
on proper layout and thermal management. The
θJA specified in the MOSFET data sheet refers to a given
copper area and thickness. In most cases, a lowest thermal impedance of 40
°C/W requires one square inch
of 2-ounce copper on a G10/FR4 board. Lower thermal impedances can be achieved at the expense of board
area. Please refer to the selected MOSFET’s data sheet for more information regarding proper mounting.
相关PDF资料
PDF描述
TPS40054PWPR SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS40054PWP SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS40054PWPRG4 SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS40055PWPG4 SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS40057PWP SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
相关代理商/技术参数
参数描述
TPS40052PWPG4 功能描述:DC/DC 开关控制器 Wide Input Sync Buck Cntrlr w/DDR trking RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
TPS40052PWPR 功能描述:DC/DC 开关控制器 Wide Input Sync Buck Cntrlr w/DDR trking RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
TPS40052PWPRG4 功能描述:DC/DC 开关控制器 Wide Input Sync Buck Cntrlr w/DDR trking RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
TPS40053 制造商:TI 制造商全称:Texas Instruments 功能描述:WIDE-INPUT SYNCHRONOUS BUCK CONTROLLER
TPS40053PWP 功能描述:DC/DC 开关控制器 Wide Input Vltg Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK