- 您现在的位置：买卖IC网 > PDF目录69509 > TPS40192DRCRG4 (TEXAS INSTRUMENTS INC) SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | TPS40192DRCRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | 3 X 3 MM, GREEN, PLASTIC, SON-10 |
| 文件页数： | 4/38页 |
| 文件大小： | 707K |
| 代理商： | TPS40192DRCRG4 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
4
1
5
To
Enable
Chip
VDD
ENABLE
GND
1.5 M
200 k
1 k
1 k
300 k
200
UDG05061
SLUS719C – MARCH 2007 – REVISED AUGUST 2010
www.ti.com
Enable Functionality
The TPS40192 and TPS40193 have a dedicated ENABLE pin. This simplifies user level interface design since
no multiplexed functions exist. Another benefit is a true low power shutdown mode of operation. When the
ENABLE pin is pulled to GND, all unnecessary functions, including the BP5 regulator, are turned off, reducing the
device IDD current to 45-A. A functionally equivalent circuit of the enable circuitry shown in Figure 12.
Figure 12. TPS40192 ENABLE Pin Internal Circuitry
If the ENABLE pin is left floating, the chip starts automatically. The pin must be pulled to less than 600 mV to
guarantee that the TPS40192/3 is in shutdown mode. Note that the ENABLE pin is relatively high impedance. In
some situations, there could be enough noise nearby to cause the ENABLE pin to swing below the 600 mV
threshold and give erroneous shutdown commands to the rest of the device. There are two solutions to solve this
problem.
1. Place a capacitor from ENABLE to GND. A side effect of this is to delay the start of the converter while the
capacitor charges past the enable threshold
2. Place a resistor from VDD to ENABLE. This causes more current to flow in the shutdown mode, but does not
delay converter startup. If a resistor is used, the total current into the ENABLE pin should be limited to no
more than 500 mA.
The ENABLE pin is self-clamping. The clamp voltage can be as low as 1 V with a 1-k
Ω ground impedance. Due
to this self-clamping feature, the pull-up impedance on the ENABLE pin should be selected to limit the sink
current to less than 500 A. Driving the ENABLE pin with a low-impedance source voltage can result in damage
to the device.
12
Copyright 2007–2010, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| TPS40192DRCTG4 | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS40193DRCR | SWITCHING CONTROLLER, 360 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS40195RGYR | SWITCHING CONTROLLER, 580 kHz SWITCHING FREQ-MAX, PQCC16 |
| TPS40195PWG4 | SWITCHING CONTROLLER, 580 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40195PW | SWITCHING CONTROLLER, 580 kHz SWITCHING FREQ-MAX, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS40192DRCT | 功能描述:DC/DC 开关控制器 4.5V-8V Input Synch Buck Contr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS40192DRCTG4 | 功能描述:DC/DC 开关控制器 4.5V-18V Input Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS40192EVM-001 | 功能描述:电源管理IC开发工具 TPS40192 Evaluation Module RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS40192EVM-525 | 功能描述:电源管理IC开发工具 TPS40192EVM-525 Eval mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS40193 | 制造商:TI 制造商全称:Texas Instruments 功能描述:4.5-V TO 18-V INPUT 10-PIN SYNCHRONOUS BUCK CONTROLLER WITH POWER GOOD |
发布紧急采购，3分钟左右您将得到回复。