- 您现在的位置：买卖IC网 > PDF目录69509 > TPS40210QDGQRQ1 (TEXAS INSTRUMENTS INC) SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | TPS40210QDGQRQ1 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | GREEN, PLATSIC, MSOP-10 |
| 文件页数： | 10/41页 |
| 文件大小： | 999K |
| 代理商： | TPS40210QDGQRQ1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
(
)
SS
BP
SS(ofst)
SS
BP
SS(ofst)
FB
t
C
V
R
ln
V
=
-
÷
÷
-
+
è
I
=
C(chg)
C
V
t
OUT
SS
t
>
SS
C
V
(I
I
)
OUT
OUT(oc)
EXT
-
SLVS861D – AUGUST 2008 – REVISED APRIL 2010
www.ti.com
The required capacitance for a given soft start time t3 – t1 in Figure 24 is calculated in Equation 13.
where
tSS is the soft-start time
RSS(chg) is the SS charging resistance in , typically 500 k
CSS is the value of the capacitor on the SS pin, in F
VBP is the value of the voltage on the BP pin in V
VSS(ofst) is the approximate level shift from the SS pin to the error amplifier (~1 V)
VFB is the error amplifier reference voltage, 700 mV typical
(13)
Note that tSS is the time it takes for the output voltage to rise from 0 V to the final output voltage. Also note the
tolerance on RSS(chg) given in the electrical specifications table. This contributes to some variability in the output
voltage rise time, and margin must be applied to account for it in design.
Also take note of VBP. Its value varies depending on input conditions. For example, a converter operating from a
slowly rising input initializes VBP at a fairly low value and increases during the entire startup sequence. If the
controller has a voltage above 8 V at the input and the DIS pin is used to stop and then restart the converter, VBP
is approximately 8 V for the entire startup sequence. The higher the voltage on BP, the shorter the startup time is
and conversely, the lower the voltage on BP, the longer the startup time is.
The soft-start time (tSS) must be chosen long enough so that the converter can start up without going into an
overcurrent state. Since the overcurrent state is triggered by sensing the peak voltage on the ISNS pin, that
voltage must be kept below the overcurrent threshold voltage VISNS(oc). The voltage on the ISNS pin is a function
of the load current of the converter, the rate of rise of the output voltage and the output capacitance, and the
current sensing resistor. The total output current that must be supported by the converter is the sum of the
charging current required by the output capacitor and any external load that must be supplied during startup. This
current must be less than the IOUT(oc) value used in Equation 6 or Equation 7 (depending on the operating mode
of the converter) to determine the current sense resistor value.
In these equations, the actual input voltage at the time that the controller reaches the final output voltage is the
important input voltage to use in the calculations. If the input voltage is slowly rising and is at less than the
nominal input voltage when the startup time ends, the output current limit is less than IOUT(oc) at the nominal input
voltage. The output capacitor charging current must be reduced (decrease COUT or increase the tSS) or IOUT(oc)
must be increased and a new value for RISNS calculated.
(14)
where
IC(chg) is the output capacitor charging current in A
COUT is the total output capacitance in F
VOUT is the output voltage in V
IOUT(oc) is the desired over current trip point in A
IEXT is any external load current in A
(15)
18
Copyright 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): TPS40210-Q1 TPS40211-Q1
相关PDF资料 |
PDF描述 |
|---|---|
| TPS40304DRCT | SWITCHING CONTROLLER, 660 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS40303DRCT | SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS40304DRCR | SWITCHING CONTROLLER, 660 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS40422RHAT | DUAL SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, QCC40 |
| TPS40422RHAR | DUAL SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, QCC40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS40210SHKK | 功能描述:电流型 PWM 控制器 Wide Inp Range Crnt Mode Boost Contrlr RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| TPS40210SKGD1 | 功能描述:电流型 PWM 控制器 Wide Inp Range Crnt Mode Boost Contrlr RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| TPS40211 | 制造商:TI 制造商全称:Texas Instruments 功能描述:4.5-V TO 52-V INPUT CURRENT MODE BOOST CONTROLLER |
| TPS40211DGQ | 功能描述:LED照明驱动器 Wide Input Rnge Crnt Mode Boost Cntrlr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| TPS40211DGQ | 制造商:Texas Instruments 功能描述:DC/DC Controllers (External Switch) IC 制造商:Texas Instruments 功能描述:IC, BOOST CONTROLLER, MSOP-10 |
发布紧急采购，3分钟左右您将得到回复。