- 您现在的位置：买卖IC网 > PDF目录13093 > TPS51020DBTG4 (Texas Instruments)IC DUAL DC/DC SYNC CTRLR 30TSSOP PDF资料下载
参数资料
| 型号： | TPS51020DBTG4 |
| 厂商： | Texas Instruments |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | IC DUAL DC/DC SYNC CTRLR 30TSSOP |
| 标准包装： | 60 |
| 应用： | 控制器，DDR，DDR2 |
| 输入电压： | 4.5 V ~ 28 V |
| 输出数： | 2 |
| 输出电压： | 0.9 V ~ 24 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 30-TFSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 30-TSSOP |
| 包装： | 管件 |
| 配用： | 296-18958-ND - EVAL MODULE FOR TPS51020-001 296-17268-ND - EVALUATION MODULE FOR TPS51100 296-12357-ND - EVAL MOD FOR TPS2330-185 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
TPS51020
SLUS564C ? JULY 2003 ? REVISED OCTOBER 2008
APPLICATION INFORMATION
SKIP MODE OPERATION
If the SKIP pin is set HIGH, the SMPS operates in the fixed PWM mode. While a LOW signal is applied, the
controller operates in autoskip mode. In the autoskip mode, the operation changes from constant frequency
PWM mode to an energy-saving skip mode automatically by detecting the edge of discontinuous current mode.
During the skip mode, the hysteretic comparator monitors output voltage to trigger high side on at the next
coming oscillator pulse after the lower level is detected. Several sequential pulses may be seen, especially in
the intermediate load level, before output capacitor is charged up to the higher level and waits for next cycle.
In the skip mode, frequency varies with load current and input voltage.
Skip mode for SMPS_2 is disabled regardless of the SKIP pin status if DDR mode is selected (see Dual Mode
and DDR Mode section). This is because current sink capability is required for V TT , so that rectifying MOSFET
needs to be kept on when the inductor current flows inversely. SMPS_1 is still capable of skip mode operation
while DDR Mode.
CASCADE CONFIGURATION
If the TRIP2 pin is tied through a resistor to the input voltage, the TPS51020 assumes that the conversion voltage
for channel two is the VIN voltage, usually VBATT. Conversely, if TRIP2 is tied through a resistor to ground, the
controller assumes that the conversion voltage for channel two is the output voltage of channel one or some
other stable bus voltage.
DUAL MODE AND DDR MODE
TPS51020 provides one-chip solution for system power supply, such as for 5 V, 3.3 V or 1.8 V, and a dual
switcher DDR power supply. By simply selecting DDR signal and some external configuration change following
the instructions below, TPS51020 gives a complete function set required for the DDR termination supply such
as VDDQ/2 tracking V TT source/sink capability and V TT reference output.
If DDR is set high ( > 2.2 V), the TPS51020 runs in dual mode, that is, each converter produces an independent
output voltage with respect to the internal 0.85-V reference. Bypass REF_X to ground by 0.01- μ F. The
VO1_VDDQ or VO2 terminal should be connected to their corresponding switcher output. The 10-V reference
output can be used as FET switch biasing for power control during sleep states (see Figure 5). During this dual
mode, selection of autoskip mode or PWM mode made by SKIP applies to both SMPS_1 and SMPS_2.
If DDR is set low ( < 0.3V), the TPS51020 operates as a dual switcher DDR supply; VDDQ from SMPS_1 and
V TT from SMPS_2 (DDR Mode). In this mode, the reference voltage for SMPS_2 is switched to (VO1_VDDQ)/2
to track exactly half the voltage of SMPS_1, divided by internal resistors. VO1_VDDQ should be connected to
SMPS_1 output terminal to accomplish this. REF_X outputs the (VO1_VDDQ)/2 voltage after a buffer (5-mA
max). SKIP controls only SMPS_1 and SMPS_2 is forced to operate in PWM mode so that current can be sink
from the output. Power source of SMPS_2 can either be the battery voltage (independent configuration), or the
VDDQ (cascade configuration) by user ’s preference. When using the independent configuration, TRIP2 needs
to be connected to the VIN node via trip resistor. In case of cascade configuration, tie TRIP2 to GND via trip
resistor (see Figure 7).
CAUTION:Do NOT toggle DDR HIGH while ENBL1 or ENBL2 is high (see Table 2). REF_X
output switches to high voltage (10 V) and be applied to V TTREF directly
www.ti.com
11
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JWW-EZ-B1 | CONVERTER MOD DC/DC 5.5V 25W |
| VE-J5N-CZ-B1 | CONVERTER MOD DC/DC 18.5V 25W |
| RBM43DRTI-S13 | CONN EDGECARD 86POS .156 EXTEND |
| VI-J1H-EZ-B1 | CONVERTER MOD DC/DC 52V 25W |
| SI9130CG-E3 | IC CTRLR PWM PIN PROG 28SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS51020DBTR | 功能描述:DC/DC 开关控制器 Dual DDR selectable Sync buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS51020DBTRG4 | 功能描述:DC/DC 开关控制器 Dual DDR selectable Sync buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS51020EVM-001 | 功能描述:电源管理IC开发工具 TPS51020-001 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS5102DBT | 制造商:TI 制造商全称:Texas Instruments 功能描述:DUAL, HIGH-EFFICIENCY CONTROLLER FOR NOTEBOOK PC POWER |
| TPS5102IDBR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。