- 您现在的位置：买卖IC网 > PDF目录150839 > TPS5633PWP (TEXAS INSTRUMENTS INC) 2 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28 PDF资料下载
参数资料
| 型号： | TPS5633PWP |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 2 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封装： | GREEN, PLASTIC, HTSSOP-28 |
| 文件页数： | 22/28页 |
| 文件大小： | 568K |
| 代理商： | TPS5633PWP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页
TPS5615, TPS5618, TPS5625, TPS5633
SYNCHRONOUS-BUCK HYSTERETIC REGULATOR CONTROLLER
SLVS177B SEPTEMBER 1998 REVISED JULY 2000
3
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
Terminal Functions
TERMINAL
I/O
DESCRIPTION
NAME
NO.
I/O
DESCRIPTION
AGND2
2
Analog ground (must be connected).
ANAGND
7
Analog ground
BIAS
9
Analog bias pin. A 1-
μF capacitor should be connected from BIAS to ANAGND.
BOOT
16
Bootstrap. A 1-
μF capacitor should be connected from BOOT to BOOTLO.
BOOTLO
18
Bootstrap low. Connect to the junction of the high-side and low-side FETs for floating drive configuration.
Connect to PGND for ground-reference drive configuration.
DRV
14
Drive regulator for the FET drivers. A 1-
μF capacitor should be connected from DRV to DRVGND.
DRVGND
12
Drive ground. Ground for FET drivers. Connect to FET PWRGND.
HIGHDR
17
High drive. Output drive to high-side power switching FETs.
HISENSE
19
High current sense. For current sensing across high-side FETs, connect to the drain of the high-side FETs;
for optional current sensing scheme, connect to power supply side of current-sense resistor placed in series
with high-side FET drain.
INHIBIT
22
Disables the drive signals to the MOSFET drivers. Also serves as UVLO for system logic supply (3.3 V or
5 V). An external pullup resistor should be connected to system-logic supply.
IOUT
1
Current out. Output voltage on this terminal is proportional to the load current as measured across the
Rds(on) of the high side FET. The voltage on this terminal equals 2 × RDS(ON) × IOUT. In applications where
very accurate current-sensing is required, a sense resistor should be connected between the input supply
and the drain of the high-side FETs.
IOUTLO
21
Current sense low output. This is the voltage on the LOSENSE terminal when the high-side FETs are on.
A ceramic capacitor (between 0.033
μF and 0.1 μF) should be connected from IOUTLO to HISENSE to hold
the sensed voltage.
LODRV
10
Low drive enable. Normally tied to 5 V. To configure the low-side FET as a crowbar, pull LODRV low.
LOHIB
11
Low side inhibit. Connect to the junction of the high- and low-side FETs to control the anti-cross-
conduction and eliminate shoot-through current. Disabled when configured in crowbar mode.
LOSENSE
20
Low current sense. For current sensing across high-side FETs, connect to the source of the high-side FETs;
for optional current sensing scheme, connect to high-side FET drain side of current-sense resistor placed
in series with high-side FET drain.
LOWDR
13
Low drive. Output drive to synchronous rectifier FETs.
NC
2327
No connect
OCP
3
Over current protection. Current limit trip point is set with a resistor divider between IOUT and ANAGND.
PWRGD
28
Power good. PWRGD signal goes high when output voltage is within 7% of voltage setpoint. Open-drain
output.
SLOWST
8
Slow Start (soft start). A capacitor form SLOWST to ANAGND sets the slowstart time.
Slowstart current = IVREFB/5
VHYST
4
Hysteresis set input. The hysteresis is set with a resistor divider from VREFB to ANAGND.
Hysteresis = 2
× (VREFB VHYST)
VCC
15
12-V supply. A 1-
μF capacitor should be connected from VCC to DRVGND.
VREFB
5
Buffered reference voltage
VSENSE
6
Voltage sense Input. To be connected from converter output voltage bus to sense and control output voltage.
It is recommended that a RC low-pass filter be connected at this pin to filter noise.
相关PDF资料 |
PDF描述 |
|---|---|
| TC74A0-3.3VAT | SPECIALTY ANALOG CIRCUIT, PSFM5 |
| TC74A7-3.3VAT | SPECIALTY ANALOG CIRCUIT, PSFM5 |
| TS3431CIZ-AP | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, PBCY3 |
| TX10005JASLPLDH | 1-OUTPUT 1000 W AC-DC PWR FACTOR CORR MODULE |
| TB6526AF | STEPPER MOTOR CONTROLLER, 0.12 A, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS5633PWPG4 | 功能描述:DC/DC 开关控制器 High Crnt Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS5633PWPR | 功能描述:DC/DC 开关控制器 High Crnt Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS5633PWPRG4 | 功能描述:DC/DC 开关控制器 High Crnt Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS563900DAPR | 功能描述:Buck Switching Regulator IC Positive Adjustable (Programmable) 0.68V 2 Output 3.5A 32-TSSOP (0.240", 6.10mm Width) Exposed Pad 制造商:texas instruments 系列:- 包装:剪切带（CT） 零件状态:有效 功能:降压 输出配置:正 拓扑:降压 输出类型:可调节（可编程） 输出数:2 电压 - 输入（最小值）:4.5V 电压 - 输入（最大值）:18V 电压 - 输出（最小值/固定）:0.68V 电压 - 输出（最大值）:1.95V 电流 - 输出:3.5A 频率 - 开关:200kHz ~ 1.6MHz 同步整流器:是 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:32-TSSOP（0.240"，6.10mm 宽）裸焊盘 供应商器件封装:32-HTSSOP 标准包装:1 |
| TPS564201DDCR | 功能描述:IC REG BUCK ADJ 4A SYNC 6SOT 制造商:texas instruments 系列:D-CAP2?? 包装:剪切带（CT） 零件状态:在售 功能:降压 输出配置:正 拓扑:降压 输出类型:可调式 输出数:1 电压 - 输入（最小值）:4.5V 电压 - 输入（最大值）:17V 电压 - 输出（最小值/固定）:0.76V 电压 - 输出（最大值）:7V 电流 - 输出:4A 频率 - 开关:560kHz 同步整流器:是 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 供应商器件封装:SOT-23-6 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。