参数资料
型号: TPS60251RTWR
厂商: TEXAS INSTRUMENTS INC
元件分类: 稳压器
英文描述: SWITCHED CAPACITOR CONVERTER, 750 kHz SWITCHING FREQ-MAX, PQCC24
封装: 4 X 4 MM, GREEN, PLASTIC, QFN-24
文件页数: 2/26页
文件大小: 783K
代理商: TPS60251RTWR
www.ti.com
x1 Operating
Area
x1.5 Operating
Area
V
I
V
I
V
O
VA
VF
VDX
CP WLEDDriver
VB
VC
VHYS
LED CURRENT SINKS (DM_, DS_)
SLVS767C – APRIL 2007 – REVISED NOVEMBER 2007
Figure 13. Input Voltage Hysteresis Between
×1 and ×1.5 Mode
As shown in Figure 13, there is input voltage hysteresis voltage between 1
× and 1.5× mode to ensure stable
operation during mode transition. For the 1 cell Li-Ion battery input voltage range, the TPS60251 operates in 1
×
mode when a fully charged battery is installed. Once the battery voltage drops below the VB level, which is the
mode transition voltage from 1
× to 1.5×, the WLED driver operates in 1.5× mode. Once in 1.5× mode, the battery
voltage must rise to the VC level in order to transition from 1.5× to 1×. This hysteresis ensures stable operation
when there is some input voltage fluctuation at the 1
×/1.5× mode transition. The WLED driver provides a typical
280mV hysteresis voltage (VHYS) that changes based on LED current, to prevent oscillating between modes.
The transition voltage, VB, depends on VDX (the mode transition threshold voltage), VF (WLED forward voltage
drop) and VA (the drop out voltage of the charge pump stage) and is calculated as follows:
VB = VA + VF + VDX
VA = ROUT1X × ILEDTOTAL
Where ROUT1X is the 1× mode output impedance of the IC. See the Electrical Characteristics table for output
impedance specifications.
The TPS60251 switches to 1.5
× mode when the input voltage is below V
B and remains in 1.5× mode as long as
the input is lower than VC. 1.5× Mode is exited when the input voltage rises above VC. VC is calculated as:
VC = VF + 550 mV
The input voltage mode transition hysteresis voltage (VHYS) between 1× and 1.5× is calculated using the following
equation.
VHYS = VC – VB = 550 mV – VDX – VA, where VDX = 100 mV
Note that VA is the key factor in determining VHYS and is dependant on the 1× mode charge pump output
impedance and WLED current.
The TPS60251 has constant current sinks which drive seven individual LED current paths. Each current sink
regulates the LED current to a constant value determined by the I2C interface. The internal register addressing
allows the LED main channels DM1~DM5 to be controlled independently from the LED sub channels DS1~DS2.
The maximum current is programmable by the user (see the Setting the LED Current section). All the LED
channels sink up to 25mA of current except DM5 which has an 80-mA maximum current when configured as an
10
Copyright 2007, Texas Instruments Incorporated
Product Folder Link(s): TPS60251
相关PDF资料
PDF描述
TPS60251RTWT SWITCHED CAPACITOR CONVERTER, 750 kHz SWITCHING FREQ-MAX, PQCC24
TPS60401DBVRG4 SWITCHED CAPACITOR CONVERTER, 28 kHz SWITCHING FREQ-MAX, PDSO5
TPS60402DBVRG4 SWITCHED CAPACITOR CONVERTER, 70 kHz SWITCHING FREQ-MAX, PDSO5
TPS61045DRBTG4 0.45 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
TPS61045DRBR 0.45 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
相关代理商/技术参数
参数描述
TPS60251RTWRG4 功能描述:LED照明驱动器 High Eff Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
TPS60251RTWT 功能描述:LED照明驱动器 High Eff Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
TPS60251RTWT 制造商:Texas Instruments 功能描述:DC/DC Charge Pump Converter IC
TPS60251RTWTG4 功能描述:LED照明驱动器 High Eff Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
TPS60252RTE 制造商:TI 制造商全称:Texas Instruments 功能描述:HIGH EFFICIENCY CHARGE PUMP FOR 7 WLEDs WITH I2C INTERFACE