- 您现在的位置：买卖IC网 > PDF目录136906 > TPS61040DRVR (TEXAS INSTRUMENTS INC) 0.45 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO6 PDF资料下载
参数资料
| 型号： | TPS61040DRVR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 0.45 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO6 |
| 封装： | 2 X 2 MM, 0.80 MM HEIGHT, GREEN, PLASTIC, SON-6 |
| 文件页数： | 21/27页 |
| 文件大小： | 779K |
| 代理商： | TPS61040DRVR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页
I
peak(typ) +
I
LIM )
V
IN
L
100 ns
I
peak(typ) +
400 mA )
V
IN
L
100 ns for the TPS61040
I
peak(typ) +
250 mA )
V
IN
L
100 ns for the TPS61041
www.ti.com
SLVS413F – OCTOBER 2002 – REVISED DECEMBER 2010
Table 2. Terminal Functions
TERMINAL
I/O
DESCRIPTION
DDC,
NAME
DRV NO.
DBV NO.
This is the enable pin of the device. Pulling this pin to ground forces the device into shutdown
EN
4
3
I
mode reducing the supply current to less than 1 mA. This pin should not be left floating and needs
to be terminated.
This is the feedback pin of the device. Connect this pin to the external voltage divider to program
FB
3
4
I
the desired output voltage.
GND
2
1
–
Ground
NC
–
5
–
No connection
Connect the inductor and the Schottky diode to this pin. This is the switch pin and is connected to
SW
1
6
I
the drain of the internal power MOSFET.
VIN
5
2
I
Supply voltage pin
DETAILED DESCRIPTION
OPERATION
The TPS61040/41 operates with an input voltage range of 1.8 V to 6 V and can generate output voltages up to
28 V. The device operates in a pulse-frequency-modulation (PFM) scheme with constant peak current control.
This control scheme maintains high efficiency over the entire load current range, and with a switching frequency
up to 1 MHz, the device enables the use of very small external components.
The converter monitors the output voltage, and as soon as the feedback voltage falls below the reference voltage
of typically 1.233 V, the internal switch turns on and the current ramps up. The switch turns off as soon as the
inductor current reaches the internally set peak current of typically 400 mA (TPS61040) or 250 mA (TPS61041).
See the Peak Current Control section for more information. The second criteria that turns off the switch is the
maximum on-time of 6 ms (typical). This is just to limit the maximum on-time of the converter to cover for extreme
conditions. As the switch is turned off the external Schottky diode is forward biased delivering the current to the
output. The switch remains off for a minimum of 400 ns (typical), or until the feedback voltage drops below the
reference voltage again. Using this PFM peak current control scheme the converter operates in discontinuous
conduction mode (DCM) where the switching frequency depends on the output current, which results in very high
efficiency over the entire load current range. This regulation scheme is inherently stable, allowing a wider
selection range for the inductor and output capacitor.
PEAK CURRENT CONTROL
The internal switch turns on until the inductor current reaches the typical dc current limit (ILIM) of 400 mA
(TPS61040) or 250 mA (TPS61041). Due to the internal propagation delay of typical 100 ns, the actual current
exceeds the dc current limit threshold by a small amount. The typical peak current limit can be calculated:
(1)
The higher the input voltage and the lower the inductor value, the greater the peak.
By selecting the TPS61040 or TPS61041, it is possible to tailor the design to the specific application current limit
requirements. A lower current limit supports applications requiring lower output power and allows the use of an
inductor with a lower current rating and a smaller form factor. A lower current limit usually has a lower output
voltage ripple as well.
Copyright 2002–2010, Texas Instruments Incorporated
3
相关PDF资料 |
PDF描述 |
|---|---|
| TES113ZD-A8 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| TC1121COA713 | SWITCHED CAPACITOR CONVERTER, 200 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC54VC212ECB723 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TC54VC3202EZB723 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBCY3 |
| TLVH431BQDCKT | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.24 V, PDSO6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS61040DRVRG4 | 功能描述:LED照明驱动器 28V 400-mA Sw Boost Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| TPS61040DRVT | 功能描述:LED照明驱动器 28V 400mA Sw Boost Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| TPS61040DRVTG4 | 功能描述:LED照明驱动器 28V 400-mA Sw Boost Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| TPS61040EVM-001 | 功能描述:电源管理IC开发工具 TPS61040 Boost Conv Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS61040EVM-002 | 功能描述:电源管理IC开发工具 TPS61040 Boost Conv Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。