- 您现在的位置：买卖IC网 > PDF目录98283 > TPS61045DRBR (TEXAS INSTRUMENTS INC) 0.45 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 PDF资料下载
参数资料
| 型号： | TPS61045DRBR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 0.45 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封装： | 3 X 3 MM, GREEN, PLASTIC, SON-8 |
| 文件页数： | 2/21页 |
| 文件大小： | 582K |
| 代理商： | TPS61045DRBR |
(
)
IN
O
IN
s(max)
P
O
V
f
=
I
L V
-
375
100
IN
P(typ)
V
I
=
m A
ns
L
+
(
)
2
LOAD
O
IN
F
S(ILOAD)
P
I
V
f
=
I
L
-
+
375
100
IN
P(typ)
V
I
m A
ns
L
=
+
t
P
fall
O
IN
I
L
V
=
-
SLVS440B – JANUARY 2003 – REVISED MARCH 2009
www.ti.com
APPLICATION INFORMATION
INDUCTOR SELECTION, MAXIMUM LOAD CURRENT
Since the PFM peak current control scheme is inherently stable the inductor and capacitor value does not affect
the stability of the regulator. The selection of the inductor together with the nominal load current, input, and
output voltage of the application determines the switching frequency of the converter. Depending on the
application, inductor values between 2.2 mH up to 47 mH are recommended. The maximum inductor value is
determined by the maximum switch on-time of 6 ms (typ). The peak current limit of 375 mA (typ) must be reached
within this 6 ms for proper operation.
The inductor value determines the maximum switching frequency of the converter. Therefore, the inductor value
must be selected for the maximum switching frequency, at maximum load current of the converter and should not
be exceeded. A good inductor value to start with is 4.7 mH. The maximum switching frequency is calculated as:
with:
IP = peak current as described in the previous peak current control section.
L = selected inductor value; per the above description inductor values between 2.2 mH up to 47 mH are
recommended.
If the selected inductor does not exceed the maximum switching frequency of the converter, as a next step, the
switching frequency at the nominal load current is estimated as follows:
with:
IP = peak current as described in the previous chapter peak current control section
L = selected inductor value
I(LOAD) = nominal load current
VF = rectifier diode forward voltage (typically 0.3 V)
The smaller the inductor value, the higher the switching frequency of the converter but the lower the efficiency.
The maximum load current of the converter is determined at the operation point where the converter starts to
enter continuous conduction mode. The converter must always operate in discontinuous conduction mode to
maintain regulation.
Two conditions exist for determining the maximum output current of the converter. One is when the inductor
current fall time is <400 ns, and the other is when the inductor current fall time is >400 ns.
One way to calculate the maximum available load current under certain operation conditions is to estimate the
expected converter efficiency at the maximum load current. This number can be taken out of the efficiency
Inductor fall time:
For tf ≥ 400 ns
10
Copyright 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS61045
相关PDF资料 |
PDF描述 |
|---|---|
| TPS61080DRCR | 1 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61081DRCTG4 | 1.3 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61080DRCTG4 | 0.5 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61093DSK | 1.5 A SWITCHING REGULATOR, 1400 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61122PWRG4 | 1.6 A BATTERY CHARGE CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS61045DRBRG4 | 功能描述:LED显示驱动器 28-V 85% Eff Boost Converter RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| TPS61045DRBT | 功能描述:LED显示驱动器 28-V 85% Eff Boost Converter RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| TPS61045DRBTG4 | 功能描述:LED照明驱动器 28-V 85% Eff Boost Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| TPS61045EVM-231 | 功能描述:电源管理IC开发工具 TPS61045-231 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS61046EVM-682 | 功能描述:TPS61046 - DC/DC, Step Up 2, Non-Isolated Outputs Evaluation Board 制造商:texas instruments 系列:- 零件状态:有效 主要用途:DC/DC，步升 输出和类型:2，非隔离 功率 - 输出:- 电压 - 输出:12V，5 V ~ 28 V 电流 - 输出:100mA，20mA 电压 - 输入:1.8 V ~ 5.5 V 稳压器拓扑:升压 频率 - 开关:1MHz 板类型:完全填充 所含物品:板 使用的 IC/零件:TPS61046 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。