参数资料
型号: TPS61092RSARG4
厂商: TEXAS INSTRUMENTS INC
元件分类: 稳压器
英文描述: 2.5 A BATTERY CHARGE CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PQCC16
封装: 4 X 4 MM, GREEN, PLASTIC, QFN-16
文件页数: 3/24页
文件大小: 753K
代理商: TPS61092RSARG4
www.ti.com
APPLICATION INFORMATION
DESIGN PROCEDURE
Programming the Output Voltage
R3 + R4
V
O
V
FB
* 1 + 200 kW
V
O
500 mV *
1
(1)
C
parR3 +
10 pF
200 kW
R4
–1
(2)
SW
C1
Power
Supply
L1
R1
R2
VBAT
VOUT
FB
C2
C3
LBO
PGND
LBI
SYNC
EN
GND
TPS6109x
VOUT
Boost Output
Low Battery
Output
R3
R4
R5
Programming the LBI/LBO Threshold Voltage
TPS61090
TPS61091, TPS61092
SLVS484A – JUNE 2003 – REVISED APRIL 2004
The TPS6109x dc/dc converters are intended for systems powered by a dual or triple cell NiCd or NiMH battery
with a typical terminal voltage between 1.8 V and 5.5 V. They can also be used in systems powered by one-cell
Li-Ion with a typical stack voltage between 2.5 V and 4.2 V. Additionally, two or three primary and secondary
alkaline battery cells can be the power source in systems where the TPS6109x is used.
The output voltage of the TPS61090 dc/dc converter section can be adjusted with an external resistor divider.
The typical value of the voltage on the FB pin is 500 mV. The maximum allowed value for the output voltage is
5.5 V. The current through the resistive divider should be about 100 times greater than the current into the FB
pin. The typical current into the FB pin is 0.01 A, and the voltage across R4 is typically 500 mV. Based on those
two values, the recommended value for R4 should be lower than 500 k
, in order to set the divider current at 1
A or higher. Because of internal compensation circuitry the value for this resistor should be in the range of 200
k
. From that, the value of resistor R3, depending on the needed output voltage (V
O), can be calculated using
Equation 1:
If as an example, an output voltage of 5.0 V is needed, a 1.8-M
resistor should be chosen for R3. If for any
reason the value for R4 is chosen significantly lower than 200 k
additional capacitance in parallel to R3 is
recommended. The required capacitance value can be easily calculated using Equation 2
Figure 18. Typical Application Circuit for Adjustable Output Voltage Option
The current through the resistive divider should be about 100 times greater than the current into the LBI pin. The
typical current into the LBI pin is 0.01 A, and the voltage across R2 is equal to the LBI voltage threshold that is
generated on-chip, which has a value of 500 mV. The recommended value for R2is therefore in the range of 500
k
. From that, the value of resistor R1, depending on the desired minimum battery voltage V
BAT, can be
calculated using Equation 3.
11
相关PDF资料
PDF描述
TPS61097-50DRSR 0.475 A BATTERY CHARGE CONTROLLER, PDSO6
TPS61097-18DRSR 0.475 A BATTERY CHARGE CONTROLLER, PDSO6
TPS61097-ADJDRSR 0.475 A BATTERY CHARGE CONTROLLER, PDSO6
TPS61097-33DRSR 0.475 A BATTERY CHARGE CONTROLLER, PDSO6
TPS61100RGERG4 1.8 A SWITCHING REGULATOR, 800 kHz SWITCHING FREQ-MAX, PQCC24
相关代理商/技术参数
参数描述
TPS61093 制造商:TI 制造商全称:Texas Instruments 功能描述:LOW INPUT BOOST CONVERTER WITH INTEGRATED POWER DIODE AND INPUT/OUTPUT ISOLATION
TPS61093DSK 制造商:TI 制造商全称:Texas Instruments 功能描述:LOW INPUT BOOST CONVERTER WITH INTEGRATED POWER DIODE AND INPUT/OUTPUT ISOLATION
TPS61093DSKR 功能描述:直流/直流开关调节器 Low In 20V/1.1A Step Up DC/DC Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
TPS61093DSKT 功能描述:直流/直流开关调节器 Low In 20V/1.1A Step Up DC/DC Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
TPS61093DSKT 制造商:Texas Instruments 功能描述:Switching Regulator IC 制造商:Texas Instruments 功能描述:IC, STEP-UP DC/DC CONVERTER, SON-10