- 您现在的位置：买卖IC网 > PDF目录69517 > TPS62067DSGR (TEXAS INSTRUMENTS INC) 2 A SWITCHING REGULATOR, 3400 kHz SWITCHING FREQ-MAX, PDSO8 PDF资料下载
参数资料
| 型号： | TPS62067DSGR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 2 A SWITCHING REGULATOR, 3400 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封装： | 2 X 2 MM, 0.75 MM HEIGHT, GREEN, PLASTIC, WSON-8 |
| 文件页数： | 5/28页 |
| 文件大小： | 1208K |
| 代理商： | TPS62067DSGR |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
www.ti.com
SLVS833A – MARCH 2010 – REVISED MAY 2010
DETAILED DESCRIPTION
OPERATION
The TPS6206x step down converter operates with typically 3MHz fixed frequency pulse width modulation (PWM)
at moderate to heavy load currents. At light load currents the converter can automatically enter Power Save
Mode and operates then in PFM (Pulse Frequency Mode) mode.
During PWM operation the converter use a unique fast response voltage mode controller scheme with input
voltage feed-forward to achieve good line and load regulation allowing the use of small ceramic input and output
capacitors. At the beginning of each clock cycle initiated by the clock signal, the High Side MOSFET switch is
turned on. The current flows now from the input capacitor via the High Side MOSFET switch through the inductor
to the output capacitor and load. During this phase, the current ramps up until the PWM comparator trips and the
control logic will turn off the switch. The current limit comparator will also turn off the switch in case the current
limit of the High Side MOSFET switch is exceeded. After a dead time preventing shoot through current, the Low
Side MOSFET rectifier is turned on and the inductor current ramps down. The current flows now from the
inductor to the output capacitor and to the load. It returns back to the inductor through the Low Side MOSFET
rectifier..
The next cycle will be initiated by the clock signal again turning off the Low Side MOSFET rectifier and turning on
the High Side MOSFET switch.
POWER SAVE MODE
At TPS62065 pulling the Mode pin low enables Power Save Mode. In TPS62067 Power Save Mode is enabled
per default. If the load current decreases, the converter enters Power Save Mode operation automatically. During
Power Save Mode the converter skips switching and operates with reduced frequency in PFM mode with a
minimum quiescent current to maintain high efficiency. The converter positions the output voltage typically +1%
above the nominal output voltage. This voltage positioning feature minimizes voltage drops caused by a sudden
load step.
The transition from PWM mode to PFM mode occurs once the inductor current in the Low Side MOSFET switch
becomes zero, which indicates discontinuous conduction mode.
During the Power Save Mode the output voltage is monitored with a PFM comparator. As the output voltage falls
below the PFM comparator threshold of VOUTnominal +1%, the device starts a PFM current pulse. For this the High
Side MOSFET switch will turn on and the inductor current ramps up. After the On-time expires the switch will be
turned off and the Low Side MOSFET switch will be turned on until the inductor current becomes zero.
The converter effectively delivers a current to the output capacitor and the load. If the load is below the delivered
current the output voltage will rise. If the output voltage is equal or higher than the PFM comparator threshold,
the device stops switching and enters a sleep mode with typ. 18A current consumption.
In case the output voltage is still below the PFM comparator threshold, further PFM current pulses will be
generated until the PFM comparator threshold is reached. The converter starts switching again once the output
voltage drops below the PFM comparator threshold due to the load current.
The PFM mode is exited and PWM mode entered in case the output current can no longer be supported in PFM
mode.
Dynamic Voltage Positioning
This feature reduces the voltage under/overshoots at load steps from light to heavy load and vice versa. It is
active in Power Save Mode and regulates the output voltage 1% higher than the nominal value. This provides
more headroom for both the voltage drop at a load step, and the voltage increase at a load throw-off.
Copyright 2010, Texas Instruments Incorporated
13
相关PDF资料 |
PDF描述 |
|---|---|
| TPS62110MRSATEP | 2.4 A SWITCHING REGULATOR, 1100 kHz SWITCHING FREQ-MAX, PQCC16 |
| TPS62112MRSATEP | 2.4 A SWITCHING REGULATOR, 1100 kHz SWITCHING FREQ-MAX, PQCC16 |
| TPS62120DCN | SWITCHING REGULATOR, PDSO8 |
| TPS62122DRVT | SWITCHING REGULATOR, PDSO6 |
| TPS62201DBVTG4 | 0.67 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS62067DSGT | 功能描述:直流/直流开关转换器 3MHz 2A Step-Down Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| TPS62067DSGT | 制造商:Texas Instruments 功能描述:VOLTAGE REGULATOR IC 制造商:Texas Instruments 功能描述:IC, STEP-DOWN CONVERTER, WSON-8 |
| TPS62067QDSGRQ1 | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 2A 8-WFDFN Exposed Pad 制造商:texas instruments 系列:汽车级，AEC-Q100 包装:剪切带（CT） 零件状态:在售 功能:降压 输出配置:正 拓扑:降压 输出类型:可调式 输出数:1 电压 - 输入（最小值）:2.9V 电压 - 输入（最大值）:6V 电压 - 输出（最小值/固定）:0.8V 电压 - 输出（最大值）:6V 电流 - 输出:2A 频率 - 开关:3MHz 同步整流器:是 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商器件封装:8-WSON（2x2） 标准包装:1 |
| TPS62080ADSGR | 功能描述:直流/直流开关转换器 1.2A High Eff Step Down Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| TPS62080ADSGT | 功能描述:直流/直流开关转换器 1.2A High Eff Step Down Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。