- 您现在的位置：买卖IC网 > PDF目录17481 > TPS62125EVM-044 (Texas Instruments)EVAL MODULE FOR TPS62125-044 PDF资料下载
参数资料
| 型号： | TPS62125EVM-044 |
| 厂商： | Texas Instruments |
| 文件页数： | 27/38页 |
| 文件大小： | 0K |
| 描述： | EVAL MODULE FOR TPS62125-044 |
| 标准包装： | 1 |
| 系列： | DCS-Control™ |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 3.3V |
| 电流 - 输出： | 300mA |
| 输入电压： | 4 ~ 17 V |
| 稳压器拓扑结构： | 降压 |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | TPS62125 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
SLVSAQ5C – MARCH 2012 – REVISED DECEMBER 2013
In DC/DC converter applications, the efficiency is essentially affected by the inductor AC resistance (i.e. quality
factor) and by the inductor DCR value. To achieve high efficiency operation, care should be taken in selecting
inductors featuring a quality factor above 25 at the switching frequency. Increasing the inductor value produces
lower RMS currents, but degrades transient response. For a given physical inductor size, increased inductance
usually results in an inductor with lower saturation current.
The total losses of the coil consist of both the losses in the DC resistance (R DC ) and the following frequency-
dependent components:
?
?
?
?
The losses in the core material (magnetic hysteresis loss, especially at high switching frequencies)
Additional losses in the conductor from the skin effect (current displacement at high frequencies)
Magnetic field losses of the neighboring windings (proximity effect)
Radiation losses
The following inductor series from different suppliers have been used with the TPS62125.
Table 4. List of Inductors
INDUCTANCE
[μH]
10 / 15
22
15
10/15
10
DCR [ ? ]
0.33 max / 0.44 max
0.36 max
0.33 max
0.44 max / 0.7 max
0.38 typ.
DIMENSIONS
[mm 3 ]
3.3 x 3.3 x 1.4
3.9 x 3.9 x 1.8
3.0 x 2.5 x 1.5
3.0 x 3.0 x 1.5
3.2 × 2.5 × 1.7
INDUCTOR
TYPE
LPS3314
LPS4018
VLF302515
LPS3015
LQH32PN
SUPPLIER
Coilcraft
Coilcraft
TDK
Coilcraft
Murata
OUTPUT CAPACITOR SELECTION
Ceramic capacitors with low ESR values provide the lowest output voltage ripple and are recommended. The
output capacitor requires either an X7R or X5R dielectric. Y5V and Z5U dielectric capacitors, aside from their
wide variation in capacitance over temperature, become resistive at high frequencies.
At light load currents the converter operates in Power Save Mode and the output voltage ripple is dependent on
the output capacitor value and the PFM peak inductor current. Higher output capacitor values minimize the
voltage ripple in PFM Mode and tighten DC output accuracy in PFM Mode. In order to achieve specified
regulation performance and low output voltage ripple, the DC-bias characteristic of ceramic capacitors must be
considered. The effective capacitance of ceramic capacitors drops with increasing DC - bias Voltage. Due to this
effect, it is recommended for output voltages above 3.3V to use at least 1 x 22μF or 2 x 10μF ceramic capacitors
on the output.
INPUT CAPACITOR SELECTION
Because of the nature of the buck converter having a pulsating input current, a low ESR input capacitor is
required for best input voltage filtering and minimizing the interference with other circuits caused by high input
voltage spikes. For most applications, a 10μF ceramic capacitor is recommended. The voltage rating and DC
bias characteristic of ceramic capacitors need to be considered. The input capacitor can be increased without
any limit for better input voltage filtering.
For applications powered from high impedance sources, a tantalum polymer capacitor should be used to buffer
the input voltage for the TPS62125. Tantalum polymer capacitors provide a constant capacitance vs. DC bias
characteristic compared to ceramic capacitors. In this case, a 10μF ceramic capacitor should be used in parallel
to the tantalum polymer capacitor to provide low ESR.
Take care when using only small ceramic input capacitors. When a ceramic capacitor is used at the input and the
power is being supplied through long wires, such as from a wall adapter, a load step at the output or V IN step on
the input can induce large ringing at the VIN pin. This ringing can couple to the output and be mistaken as loop
instability or could even damage the part by exceeding the maximum ratings. In case the power is supplied via a
connector e.g. from a wall adapter, a hot-plug event can cause voltage overshoots on the VIN pin exceeding the
absolute maximum ratings and can damage the device, too. In this case a tantalum polymer capacitor or
Copyright ? 2012–2013, Texas Instruments Incorporated
27
相关PDF资料 |
PDF描述 |
|---|---|
| PVG5H504C03R00 | TRIMMER 500K OHM 0.25W SMD |
| MIC94084YFT TR | IC LOAD SWITCH HI SIDE 2A 4-TMLF |
| MAX6023EBT25+T | IC VREF SERIES PREC 2.5V 5-UCSP |
| VLF302512MT-220M | INDUCTOR POWER 22UH .43A SMD |
| RGP10KEHE3/73 | DIODE GPP 1A 800V 500NS DO-41 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS6213013AQRGTRQ1 | 功能描述:IC REG BUCK 1.3V 3A 16VFQFN 制造商:texas instruments 系列:汽车级，AEC-Q100，DCS-Control? 包装:剪切带（CT） 零件状态:在售 功能:降压 输出配置:正 拓扑:降压 输出类型:固定 输出数:1 电压 - 输入（最小值）:3V 电压 - 输入（最大值）:17V 电压 - 输出（最小值/固定）:1.3V 电压 - 输出（最大值）:- 电流 - 输出:3A 频率 - 开关:2.5MHz 同步整流器:是 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:16-VFQFN 裸露焊盘 供应商器件封装:16-QFN（3x3） 标准包装:1 |
| TPS6213013AQRGTTQ1 | 功能描述:IC REG BUCK 1.3V 3A 16VQFN 制造商:texas instruments 系列:- 包装:剪切带（CT） 零件状态:在售 功能:降压 输出配置:正 拓扑:降压 输出类型:固定 输出数:1 电压 - 输入（最小值）:3V 电压 - 输入（最大值）:17V 电压 - 输出（最小值/固定）:1.3V 电压 - 输出（最大值）:- 电流 - 输出:3A 频率 - 开关:2.5MHz 同步整流器:是 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:16-VFQFN 裸露焊盘 供应商器件封装:16-QFN（3x3） 标准包装:1 |
| TPS62130AQRGTRQ1 | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.9V 1 Output 3A 16-VFQFN Exposed Pad 制造商:texas instruments 系列:汽车级，AEC-Q100，DCS-Control? 包装:剪切带（CT） 零件状态:有效 功能:降压 输出配置:正 拓扑:降压 输出类型:可调式 输出数:1 电压 - 输入（最小值）:3V 电压 - 输入（最大值）:17V 电压 - 输出（最小值/固定）:0.9V 电压 - 输出（最大值）:6V 电流 - 输出:3A 频率 - 开关:2.5MHz 同步整流器:是 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:16-VFQFN 裸露焊盘 供应商器件封装:16-QFN（3x3） 标准包装:1 |
| TPS62130AQRGTTQ1 | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.9V 1 Output 3A 16-VFQFN Exposed Pad 制造商:texas instruments 系列:汽车级，AEC-Q100，DCS-Control? 包装:剪切带（CT） 零件状态:有效 功能:降压 输出配置:正 拓扑:降压 输出类型:可调式 输出数:1 电压 - 输入（最小值）:3V 电压 - 输入（最大值）:17V 电压 - 输出（最小值/固定）:0.9V 电压 - 输出（最大值）:6V 电流 - 输出:3A 频率 - 开关:2.5MHz 同步整流器:是 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:16-VFQFN 裸露焊盘 供应商器件封装:16-QFN（3x3） 标准包装:1 |
| TPS62130ARGTR | 制造商:Texas Instruments 功能描述:IC REG BUCK SYNC ADJ 3A 16QFN 制造商:Texas Instruments 功能描述:Buck Converter |
发布紧急采购，3分钟左右您将得到回复。