- 您现在的位置：买卖IC网 > PDF目录300041 > TPS75425QPWPREP (TEXAS INSTRUMENTS INC) 2.5 V FIXED POSITIVE LDO REGULATOR, PDSO20 PDF资料下载
参数资料
| 型号： | TPS75425QPWPREP |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 固定正电压单路输出LDO稳压器 |
| 英文描述： | 2.5 V FIXED POSITIVE LDO REGULATOR, PDSO20 |
| 封装： | PLASTIC, HTSSOP-20 |
| 文件页数： | 18/31页 |
| 文件大小： | 608K |
| 代理商： | TPS75425QPWPREP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
TPS75201EP, TPS75215EP, TPS75218EP, TPS75225EP, TPS75233EP WITH RESET
TPS75401EP, '75415EP, '75418EP, '75425EP, '75433EP WITH POWER GOOD
FAST TRANSIENT RESPONSE 2A LOW DROPOUT VOLTAGE REGULATORS
SGLS165 APRIL 2003
25
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
THERMAL INFORMATION
thermally enhanced TSSOP-20 (PWP PowerPad
) (continued)
If the system implements a TPS75233QPWPEP regulator, where VI = 5 V and IO = 800 mA, the internal power
dissipation is:
P
D(total) +
V
I *
V
O
I
O +
(5
* 3.3)
0.8
+ 1.36 W
(9)
Comparing PD(total) with PD(max) reveals that the power dissipation in this example does not exceed the calculated
limit. When it does, one of two corrective actions should be made: raising the power-dissipation limit by increasing
the airflow or the heat-sink area, or lowering the internal power dissipation of the regulator by reducing the input
voltage or the load current. In either case, the above calculations should be repeated with the new system
parameters.
mounting information
The primary requirement is to complete the thermal contact between the thermal pad and the PWB metal. The
thermal pad is a solderable surface and is fully intended to be soldered at the time the component is mounted.
Although voiding in the thermal-pad solder-connection is not desirable, up to 50% voiding is acceptable. The data
included in Figures 26 and 27 is for soldered connections with voiding between 20% and 50%. The thermal analysis
shows no significant difference resulting from the variation in voiding percentage.
Figure 29 shows the solder-mask land pattern for the
PWP package. The minimum recommended heat-
sink area is also illustrated. This is simply a copper
plane under the body extent of the package, including
metal routed under terminals 1, 10, 11, and 20.
Figure 29. PWP Package Land Pattern
Location of Exposed
Thermal Pad on
PWP Package
Minimum Recommended
Heat-Sink Area
相关PDF资料 |
PDF描述 |
|---|---|
| TPSMC10A/7 | 1500 W, UNIDIRECTIONAL, SILICON, TVS DIODE, DO-214AB |
| TPSMC43A/7 | 1500 W, UNIDIRECTIONAL, SILICON, TVS DIODE, DO-214AB |
| TPSMC6.8A/7 | 1500 W, UNIDIRECTIONAL, SILICON, TVS DIODE, DO-214AB |
| TPT-MR-04-CCDF5 | FIBER OPTIC TRANSCEIVER, 1529-1564nm, 11300Mbps(Tx), 11300Mbps(Rx), PANEL MOUNT, FC/UPC CONNECTOR |
| TPT-MR-04-CCDFF | FIBER OPTIC TRANSCEIVER, 1529-1564nm, 11300Mbps(Tx), 11300Mbps(Rx), PANEL MOUNT, FC/UPC CONNECTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS75425QPWPRG4 | 功能描述:低压差稳压器 - LDO Fast-Tran-Resp 2-A RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| TPS75433QPWP | 功能描述:低压差稳压器 - LDO Fast-Tran-Resp 2-A RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| TPS75433QPWPG4 | 功能描述:低压差稳压器 - LDO Fast-Tran-Resp 2-A RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| TPS75433QPWPR | 功能描述:低压差稳压器 - LDO Fast-Tran-Resp 2-A RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| TPS75433QPWPRG4 | 功能描述:低压差稳压器 - LDO Fast-Tran-Resp 2-A RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。