- 您现在的位置：买卖IC网 > PDF目录136945 > TPS82678SIP (TEXAS INSTRUMENTS INC) 0.6 A SWITCHING REGULATOR, 6000 kHz SWITCHING FREQ-MAX, BGA8 PDF资料下载
参数资料
| 型号： | TPS82678SIP |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 0.6 A SWITCHING REGULATOR, 6000 kHz SWITCHING FREQ-MAX, BGA8 |
| 封装： | 2.30 X 2.90 MM, 1 MM HEIGHT, LEAD FREE, USIP-8 |
| 文件页数： | 11/28页 |
| 文件大小： | 943K |
| 代理商： | TPS82678SIP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
SLVSAI0A
– OCTOBER 2010 – REVISED APRIL 2011
APPLICATION INFORMATION
INPUT CAPACITOR SELECTION
Because of the pulsating input current nature of the buck converter, a low ESR input capacitor is required to
prevent large voltage transients that can cause misbehavior of the device or interference in other circuits in the
system.
For most applications, the input capacitor that is integrated into the TPS8267x should be sufficient. If the
application exhibits a noisy or erratic switching frequency, experiment with additional input ceramic capacitance
to find a remedy.
The TPS8267x uses a tiny ceramic input capacitor. When a ceramic capacitor is combined with trace or cable
inductance, such as from a wall adapter, a load step at the output can induce ringing at the VIN pin. This ringing
can couple to the output and be mistaken as loop instability or can even damage the part. In this circumstance,
additional "bulk" capacitance, such as electrolytic or tantalum, should be placed between the input of the
converter and the power source lead to reduce ringing that can occur between the inductance of the power
source leads and CI.
OUTPUT CAPACITOR SELECTION
The advanced, fast-response, voltage mode, control scheme of the TPS8267x allows the use of a tiny ceramic
output capacitor (CO). For most applications, the output capacitor integrated in the TPS8267x is sufficient.
At nominal load current, the device operates in PWM mode; the overall output voltage ripple is the sum of the
voltage step that is caused by the output capacitor ESL and the ripple current that flows through the output
capacitor impedance. At light loads, the output capacitor limits the output ripple voltage and provides holdup
during large load transitions.
The TPS8267x is designed as a Point-Of-Load (POL) regulator, to operate stand-alone without requiring any
additional capacitance. Adding a 2.2
μF ceramic output capacitor (X7R or X5R dielectric) generally works from a
converter stability point of view, but does not necessarily help to minimize the output ripple voltage.
For best operation (i.e. optimum efficiency over the entire load current range, proper PFM/PWM auto transition),
the TPS8267xSIP requires a minimum output ripple voltage in PFM mode. The typical output voltage ripple is ca.
1% of the nominal output voltage VO. The PFM pulses are time controlled resulting in a PFM output voltage
ripple and PFM frequency that depends (first order) on the capacitance seen at the MicroSiPTM DC/DC
converter's output.
In applications requiring additional output bypass capacitors located close to the load, care should be taken to
ensure proper operation. If the converter exhibits marginal stability or erratic switching frequency, experiment
with additional low value series resistance (e.g. 50 to 100m
Ω) in the output path to find a remedy.
Because the damping factor in the output path is directly related to several resistive parameters (e.g. inductor
DCR, power-stage rDS(on), PWB DC resistance, load switches rDS(on) …) that are temperature dependant, the
converter small and large signal behavior must be checked over the input voltage range, load current range and
temperature range.
The easiest sanity test is to evaluate, directly at the converter
’s output, the following aspects:
PFM/PWM efficiency
PFM/PWM and forced PWM load transient response
During the recovery time from a load transient, the output voltage can be monitored for settling time, overshoot or
ringing that helps judge the converter
’s stability. Without any ringing, the loop has usually more than 45° of phase
margin.
Copyright
2010–2011, Texas Instruments Incorporated
19
相关PDF资料 |
PDF描述 |
|---|---|
| TC151B2912EOA723 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151B1717EOA713 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151B3017EOA723 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151A3320EOA723 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151A5339EOA723 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS8267XEVM | 制造商:TI 制造商全称:Texas Instruments 功能描述:The TPS82671 and TPS82675 devices are series of high-frequency, synchronous, step-down dc-dc converters optimized for battery-powered portable applications |
| TPS8268090SIPT | 功能描述:Buck Switching Regulator IC Positive Fixed 0.9V 1 Output 1.6A 9-SMD Module 制造商:texas instruments 系列:- 包装:剪切带（CT） 零件状态:有效 功能:降压 输出配置:正 拓扑:降压 输出类型:固定 输出数:1 电压 - 输入（最小值）:2.5V 电压 - 输入（最大值）:5.5V 电压 - 输出（最小值/固定）:0.9V 电压 - 输出（最大值）:- 电流 - 输出:1.6A 频率 - 开关:5.5MHz 同步整流器:是 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:9-SMD 模块 供应商器件封装:9-USIP 标准包装:1 |
| TPS8268105SIPT | 功能描述:Buck Switching Regulator IC Positive Fixed 1.05V 1 Output 1.6A 9-SMD Module 制造商:texas instruments 系列:- 包装:剪切带（CT） 零件状态:有效 功能:降压 输出配置:正 拓扑:降压 输出类型:固定 输出数:1 电压 - 输入（最小值）:2.5V 电压 - 输入（最大值）:5.5V 电压 - 输出（最小值/固定）:1.05V 电压 - 输出（最大值）:- 电流 - 输出:1.6A 频率 - 开关:5.5MHz 同步整流器:是 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:9-SMD 模块 供应商器件封装:9-USIP 标准包装:1 |
| TPS8268120SIPR | 功能描述:Buck Switching Regulator IC Positive Fixed 1.2V 1 Output 1.6A 9-VBGA 制造商:texas instruments 系列:- 包装:剪切带（CT） 零件状态:有效 功能:降压 输出配置:正 拓扑:降压 输出类型:固定 输出数:1 电压 - 输入（最小值）:2.5V 电压 - 输入（最大值）:5.5V 电压 - 输出（最小值/固定）:1.2V 电压 - 输出（最大值）:- 电流 - 输出:1.6A 频率 - 开关:5.5MHz 同步整流器:是 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:9-VBGA 供应商器件封装:9-USIP 标准包装:1 |
| TPS8268120SIPT | 功能描述:Buck Switching Regulator IC Positive Fixed 1.2V 1 Output 1.6A 9-VBGA 制造商:texas instruments 系列:- 包装:剪切带（CT） 零件状态:有效 功能:降压 输出配置:正 拓扑:降压 输出类型:固定 输出数:1 电压 - 输入（最小值）:2.5V 电压 - 输入（最大值）:5.5V 电压 - 输出（最小值/固定）:1.2V 电压 - 输出（最大值）:- 电流 - 输出:1.6A 频率 - 开关:5.5MHz 同步整流器:是 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:9-VBGA 供应商器件封装:9-USIP 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。