- 您现在的位置：买卖IC网 > PDF目录98286 > TRC1300D (TEXAS INSTRUMENTS INC) RF, REMOTE CONTROL SUPPORT CIRCUIT, PDSO14 PDF资料下载
参数资料
| 型号： | TRC1300D |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 摇控器 |
| 英文描述： | RF, REMOTE CONTROL SUPPORT CIRCUIT, PDSO14 |
| 封装： | PLASTIC, SO-14 |
| 文件页数： | 21/27页 |
| 文件大小： | 358K |
| 代理商： | TRC1300D |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页
TRC1300, TRC1315
MARCSTAR
I E/D
REMOTE CONTROL ENCODER/DECODERS
SLWS011D – AUGUST 1996 – REVISED JANUARY 1997
3
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
NAME
D
N
CONF
2
I
Device configuration select. When CONF is held at a high logic level, the device assumes the encoder
mode. CONF is internally pulled up, and no connection to CONF is required for the encoder mode of
operation. When CONF is held at a low logic level at power up, the device assumes the decoder mode.
Note that this terminal is read only at device power up; CONF must be tied to GND
before VCC is applied
to select the decoder mode.
DIN/DOUT
1
I/O
Serial data input/output. In the decoder mode, DIN/DOUT becomes an input to receive serial data from
up to four remote encoders. In the learn mode, DIN/DOUT becomes an input to learn code from up
to four remote encoders. In the encoder mode, DIN/DOUT becomes an output for the encoded data.
DIN/DOUT is clocked by the internal variable oscillator.
GND
7
8
Analog and logic ground
LED
4
O
Status indicator. The LED terminal goes low, causing an LED connected from VCC (anode) to the LED
terminal (cathode) through a current-limiting resistor to light, indicating the following conditions:
Encoder mode. When the device is configured as an encoder, the LED terminal is active during
the transmission of data (including the blank time between frames).
Program mode (encoder). When the device is configured as an encoder and placed in the
program mode, the LED terminal is active until the device has generated and stored a new 40-bit
security code.
Learn mode (decoder). When the device is configured as a decoder and placed in the program
mode, the LED terminal is active until the device has successfully stored 40 bits of security code
received from an encoder through terminal DIN/DOUT.
Test mode. When the device is placed in the self-test mode, the results are indicated by flashing
the LED connected to the LED terminal.
OSCC
5
I/O
Internal oscillator frequency control. A capacitor connected from OSCC to GND and a resistor
connected from OSCR to OSCC determine the frequency of the internal oscillator.
OSCR
6
7
I/O
Internal oscillator frequency control. A resistor connected from OSCR to OSCC and a capacitor
connected from OSCC to GND determine the frequency of the internal oscillator.
PROG
3
I
Programming enable. When PROG is held at a logic-high, device enters the programming mode. In
the encoder mode, a new 40-bit security code is generated and stored in EEPROM. In the decoder
mode, the device enters a learn cycle that continues until it has successfully received 40 bits of code
from an encoder and stored them in EEPROM. PROG is internally pulled down and debounced.
TEST
12
14
I
Test mode select. When TEST is momentarily taken high, the device enters a self-test mode with the
results of the self-test mode displayed by flashing the LED connected to the LED terminal. TEST is
internally pulled down.
VCC
(TRC1300)
13
15
Not used.
VCC
(TRC1315)
13
15
Power supply input for the TRC1315 only. The voltage range for VCC is 4.5 V to 15 V. A 0.1-F bypass
capacitor should be connected from VCC to GND.
VCC/CAP
(TRC1300)
14
16
Power supply input for the TRC1300 only. The voltage range for VCC/CAP is 2.7 V to 6 V. A 0.1-F
bypass capacitor should be connected from VCC/CAP to GND.
VCC/CAP
(TRC1315)
14
16
Regulated voltage output for the TRC1315 only. This terminal provides a regulated 4.5 V to 5.5 V
output. A 1-
F and a 0.1-F bypass capacitor should be connected from VCC/CAP to GND.
相关PDF资料 |
PDF描述 |
|---|---|
| TRC1315N | RF, REMOTE CONTROL SUPPORT CIRCUIT, PDIP16 |
| TRC1315DR | RF, REMOTE CONTROL SUPPORT CIRCUIT, PDSO14 |
| TRC1315D | RF, REMOTE CONTROL SUPPORT CIRCUIT, PDSO14 |
| TRF7960RHBR | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| TRF7960RHBT | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TRC1300N | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TRC1315 | 制造商:TI 制造商全称:Texas Instruments 功能描述:MARCSTAR I E/D REMOTE CONTROL ENCODER/DECODERS |
| TRC1315D | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TRC1315N | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TRC1331S-501 | 功能描述:LED TRIPLE 1.1W COOL WHITE 30DEG RoHS:是 类别:光电元件 >> LED - 高亮度电源模块 系列:1W-型 标准包装:36 系列:5027 TFFC STAR K2 颜色:暖白色 配置:星形 在特定电流下的光通量 - 测试:75lm 电流 - 测试:350mA 电流 - 最大:1.5A 带连接器:无 驱动器电路:无 波长:- 电压:- |
发布紧急采购，3分钟左右您将得到回复。