参数资料
型号: TS34118CD
厂商: Taiwan Semiconductor Co., Ltd.
英文描述: Voice Switched Speakerphone Circuit
中文描述: 语音开关扬声器电路
文件页数: 15/20页
文件大小: 328K
代理商: TS34118CD
TS34118
15-20
2004/09 rev. B
Design Equations
2) To provide a reasonable signal level to the TLI2 level detector; and 3)to minimize any gain applied to broadband
noise generated within the attenuator. However, to cover the normal voice band, the microphone amplifier’s gain
should not exceed 48dB. For the circuit of Figure 10, the gain of the microphone amplifier was set at 35V/V (31dB),
and the differential gain of the hybrid amplifiers was set at 10.2V/V (20.1dB).
II) Receive Gain
The overall receive gain depends on the incoming signal level, and the desired output power at the speaker. Normal
receive levels (independent of the peaks) at Tip/Ring can be 35mVrms (-27dBm). Although on long lines That level can
be down to 8.0mVrms (-40dBm).The speaker power is:
0.6
10dBm/10
×
(Equation 1)
PSPK =
Rs
Where R
S
is the speaker impedance, and the dBm term is the incoming signal level increased by the gain of the receive
path. Experience has shown that
30dB gain is a satisfactory amount for the majority of applications. Using the above
numbers and Equation 1, it would appear that the resulting power to the speaker is extremely low. However, Equation 1
does not consider the peaks in normal speech, which can be 10 to 15 times the rms value. Considering the peaks, the
overall average power approaches 20-30mV on long lines, and much more on short lines.
Referring to Figure 10, the gain from Tip/Ring to the filter input was measured at 0.833V/V (-1.6dB), the filter’s gain is
unity, and the receive attenuator’s gain is 2.0V/V (+6.0dB) at maximum volume. The speaker amplifier’s gain is set at
22V/V (26.8dB), which puts the overall gain at
31.2dB.
III) Loop Gain
The total loop gain must add up to less than zero dB to obtain a stable circuit. This can be expressed as:
G
MA
+G
TX
+G
HA
+G
ST
+G
FO
+G
RX
+G
SA
+G
AC
<0
(Equation 2)
Using the typical numbers mentioned above, and knowing that G
TX
+G
RX
=-40dB, the required acoustic coupling can be
determined:
G
AC
<-[31+20.1+(-15)+0+(-40)+26.8]=-22.9dB (Equation 3)
An acoustic loss of at least 23 dB is necessary to prevent instability and oscillations, commonly referred to as “singing.”
However, the following equations show that greater acoustic loss is necessary to obtain proper level detection and
switching.
IV) Switching Threshold
To switch comparator C1, currents I1 and I3 need to be determined. Referring to Figure 11, with a receive signal V
L
applied to Tip/Ring, a current I3 will flow through R3 into RLI2 according to the following equation:
V
L
2
Where the terms in the brackets are the V/V gain terms. The speaker amplifier gain is divided by two since G
SA
is the
differential gain of the amplifier, and V3 is obtained from one the side of the output. The current I1, coming from the
microphone circuit, is defined by:
G
V
MA
(Equation 5)
I3 =
R3
×
×
×
G
G
G
G
SA
RX
FO
HR
(Equation 4)
I1 =
R1
M
×
Where V
M
is the microphone voltage. Since the switching threshold occurs when I1=I3, combining the above two
equations yields:
R1
[
2
G
MA
×
V
M
= V
L
×
R3
]
G
G
G
G
SA
RX
FO
HR
×
×
(Equation 6)
相关PDF资料
PDF描述
TS34118CS Voice Switched Speakerphone Circuit
TS34119 Low Power Audio Amplifier
TS34119CD Low Power Audio Amplifier
TS34119CS Low Power Audio Amplifier
TS34119CA COAXIAL T CNNCTRS NON-BH BNC AUTO T-CNNCTR F-M-F
相关代理商/技术参数
参数描述
TS34118CD28C4 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:Voice Switched Speakerphone Circuit
TS34118CS 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:Voice Switched Speakerphone Circuit
TS34118CS28 功能描述:电信语音调制 IC Voice Switch Speaker phone Circuit RoHS:否 制造商:Epson Electronics America 产品: 应用:Voice Guidance product 封装 / 箱体:PQFP-52 电源电压-最大:3.6 V, 5.5 V 最大工作温度: 最小工作温度: 封装:
TS34118CS28 C8 制造商:SKMI/Taiwan 功能描述:Voice Switched Speakerphone Circuit 28-Pin SOP Tube
TS34118CS28C8 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:Voice Switched Speakerphone Circuit