- 您现在的位置：买卖IC网 > PDF目录373702 > TS34118CD (Taiwan Semiconductor Co., Ltd.) Voice Switched Speakerphone Circuit PDF资料下载
参数资料
| 型号： | TS34118CD |
| 厂商： | Taiwan Semiconductor Co., Ltd. |
| 英文描述： | Voice Switched Speakerphone Circuit |
| 中文描述： | 语音开关扬声器电路 |
| 文件页数： | 18/20页 |
| 文件大小： | 328K |
| 代理商： | TS34118CD |
TS34118
18-20
2004/09 rev. B
Application Information
Dial Tone Detector
The threshold for the dial tone detector is internally set at 15mV (10mVrms) below V
B
(see Figure 5). That threshold can
be reduced by connecting a resistor from RXI to ground. The resistor value is calculated from:
R =
1
V
V
10K
B
Where V
B
is the voltage at Pin 15, and
V is the amount of threshold reduction. By connecting a resistor from Vcc to
RXI, the threshold can be increased. The resistor value is calculated from:
R =
1
V
V
V
10K
B
CC
Where
V is the amount of threshold increase.
Background Noise Monitors
For testing or circuit analysis purposes, the transmit or receive attenuators can be set to the “on” position, by disabling
the background noise monitors, and applying a signal so as to activate the level detectors. Grounding the CPR pin will
disable the receive background noise monitor, thereby indicating the “presence of speech” to the attenuator control
block. Grounding CPT does the same for the transmit path.
Additionally, the receive background noise monitor is automatically disabled by the dial tone detector whenever the
receive signal exceeds the detector’s threshold.
Transmit / Receive Detection Priority
Although the TS34118 was designed to have an idle mode such that the attenuators are halfway between their full on
and full off positions, the idle mode can be biased towards the transmit or the receive side. With this done, gaining
control of the circuit from idle will be easier for that side towards which it is biased since that path will have less
attenuation at idle.
By connecting a resistor from C
T
(pin 14) to ground, the circuit will be biased towards the transmit side. The resistor
value is calculated from:
R =
1
V
VB
R
T
Where R is the added resistor, R
T
is the resistor normally between pins 14 and 15 (typically 120
), and
V is the
difference between V
B
and the voltage at C7 at idle C refer to (Figure 10)
By connecting a resistor from C
T
(pin 14) to Vcc, the circuit will be biased towards the transmit side. The resistor value
is calculated from:
R =
1
V
V
V
R
B
CC
T
R, R
T
, and
V are the same as above. Switching time will be somewhat affected in each case due to the different
voltage excursions required to get to transmit and receive from idle. For practical considerations, the
V shift should not
exceed 100mV.
相关PDF资料 |
PDF描述 |
|---|---|
| TS34118CS | Voice Switched Speakerphone Circuit |
| TS34119 | Low Power Audio Amplifier |
| TS34119CD | Low Power Audio Amplifier |
| TS34119CS | Low Power Audio Amplifier |
| TS34119CA | COAXIAL T CNNCTRS NON-BH BNC AUTO T-CNNCTR F-M-F |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TS34118CD28C4 | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:Voice Switched Speakerphone Circuit |
| TS34118CS | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:Voice Switched Speakerphone Circuit |
| TS34118CS28 | 功能描述:电信语音调制 IC Voice Switch Speaker phone Circuit RoHS:否 制造商:Epson Electronics America 产品: 应用:Voice Guidance product 封装 / 箱体:PQFP-52 电源电压-最大:3.6 V, 5.5 V 最大工作温度: 最小工作温度: 封装: |
| TS34118CS28 C8 | 制造商:SKMI/Taiwan 功能描述:Voice Switched Speakerphone Circuit 28-Pin SOP Tube |
| TS34118CS28C8 | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:Voice Switched Speakerphone Circuit |
发布紧急采购，3分钟左右您将得到回复。