- 您现在的位置：买卖IC网 > PDF目录69531 > TS3A4751RGYR (TEXAS INSTRUMENTS INC) QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, PQCC14 PDF资料下载
参数资料
| 型号： | TS3A4751RGYR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 多路复用及模拟开关 |
| 英文描述： | QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, PQCC14 |
| 封装： | GREEN, PLASTIC, QFN-14 |
| 文件页数： | 22/23页 |
| 文件大小： | 796K |
| 代理商： | TS3A4751RGYR |
APPLICATION INFORMATION
Logic Inputs
Analog Signal Levels
Layout
SCDS227D – JULY 2006 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com
Proper power-supply sequencing is recommended for all CMOS devices. Do not exceed the absolute maximum
ratings because stresses beyond the listed ratings can cause permanent damage to the devices. Always
sequence V+ on first, followed by NO or COM.
Although it is not required, power-supply bypassing improves noise margin and prevents switching noise
propagation from the V+ supply to other components. A 0.1-F capacitor, connected from V+ to GND, is
adequate for most applications.
The TS3A4751 logic inputs can be driven up to 3.6 V, regardless of the supply voltage. For example, with a
1.8-V supply, IN may be driven low to GND and high to 3.6 V. Driving IN rail to rail minimizes power
consumption.
Analog signals that range over the entire supply voltage (V+ to GND) can be passed with very little change in ron
(see Typical Operating Characteristics). The switches are bidirectional, so NO and COM can be used as either
inputs or outputs.
High-speed switches require proper layout and design procedures for optimum performance. Reduce stray
inductance and capacitance by keeping traces short and wide. Ensure that bypass capacitors are as close to the
device as possible. Use large ground planes where possible.
8
Copyright 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): TS3A4751
相关PDF资料 |
PDF描述 |
|---|---|
| TS3A4751RUCR | QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, PQCC14 |
| TS3A5018RGYR | QUAD 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, PQCC16 |
| TS3A5018DGVRE4 | QUAD 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, PDSO16 |
| TS3A5018D | QUAD 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, PDSO16 |
| TS3A5018PW | QUAD 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TS3A4751RGYRG4 | 功能描述:模拟开关 IC Quad SPST 0.9-Ohm Switch RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| TS3A4751RUCR | 功能描述:模拟开关 IC 0.9O Lo-Vltg Sgl-Spl Quad SPST Ana Sw RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| TS3A5017 | 制造商:TI 制造商全称:Texas Instruments 功能描述:14-OHM DUAL SP4T ANALOG SWITCH 3.3-V/2.5-V DUAL 4:1 ANALOG MULTIPLEXER/DEMULTIPLEXER |
| TS3A5017_10 | 制造商:TI 制造商全称:Texas Instruments 功能描述:DUAL SP4T ANALOG SWITCH 3.3-V/2.5-V DUAL 4:1 ANALOG MULTIPLEXER/DEMULTIPLEXER |
| TS3A5017D | 功能描述:模拟开关 IC 14-Ohm Dual SP4T Analog Switch RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
发布紧急采购，3分钟左右您将得到回复。