- 您现在的位置：买卖IC网 > PDF目录272328 > TS80C51BH (INTEL CORP) 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP44 PDF资料下载
参数资料
| 型号： | TS80C51BH |
| 厂商： | INTEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP44 |
| 封装： | QFP-44 |
| 文件页数： | 17/21页 |
| 文件大小： | 2233K |
| 代理商： | TS80C51BH |
87C51/80C51BH/80C31BH
In normal operation ALE is emitted at a constant
rate of 1/6 the oscillator frequency, and may be
used for external timing or clocking purposes. Note,
however, that one ALE pulse is skipped during each
access to external Data Memory.
PSEN
: Program Store Enable is the Read strobe to
External Program Memory. When the 87C51/BH is
executing from Internal Program Memory, PSEN is
inactive (high). When the device is executing code
from External Program Memory, PSEN is activated
twice each machine cycle, except that two PSEN
activations are skipped during each access to Exter-
nal Data Memory.
EA/V PP: External Access enable. EA must be
strapped to VSS in order to enable the 87C51/BH to
fetch code from External Program Memory locations
starting at 0000H up to FFFFH. Note, however, that
if either of the Lock Bits is programmed, the logic
level at EA is internally latched during reset.
EA must be strapped to VCC for internal program
execution.
This pin also receives the programming supply volt-
age (VPP) during EPROM programming.
XTAL1
: Input to the inverting oscillator amplifier.
XTAL2
: Output from the inverting oscillator amplifi-
er.
272335±5
Figure 3. Using the On-Chip Oscillator
OSCILLATOR CHARACTERISTICS
XTAL1 and XTAL2 are the input and output, respec-
tively, of an inverting amplifier which can be config-
ured for use as an on-chip oscillator, as shown in
Figure 3.
To drive the device from an external clock source,
XTAL1 should be driven, while XTAL2 is left uncon-
nected, as shown in Figure 4. There are no require-
ments on the duty cycle of the external clock signal,
since the input to the internal clocking circuitry is
through a divide-by-two flip-flop, but minimum and
maximum high and low times specified on the data
sheet must be observed.
An external oscillator may encounter as much as a
100 pF load at XTAL1 when it starts up. This is due
to interaction between the amplifier and its feedback
capacitance. Once the external signal meets the VIL
and VIH specifications the capacitance will not ex-
ceed 20 pF.
272335±6
Figure 4. External Clock Drive
5
相关PDF资料 |
PDF描述 |
|---|---|
| TSC80C31-30CXB | 8-BIT, 30 MHz, MICROCONTROLLER, UUC40 |
| T83C154DXXX-20 | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP44 |
| TA80486DX2-50 | 32-BIT, 50 MHz, MICROPROCESSOR, CPGA168 |
| T80C32U-S:D | 8-BIT, 20 MHz, MICROCONTROLLER, PQFP44 |
| T83C154DUFXXX-30:R | 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PQFP44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TS80C51BH-1 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
| TS80C51BH-2 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
| TS80C51BH-24 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
| TS80C51BHP | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
| TS80C51BHP-1 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
发布紧急采购，3分钟左右您将得到回复。