- 您现在的位置：买卖IC网 > PDF目录244164 > TS80C51RD2-EER (ATMEL CORP) 8-BIT, MICROCONTROLLER, PQFP44 PDF资料下载
参数资料
| 型号： | TS80C51RD2-EER |
| 厂商： | ATMEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MICROCONTROLLER, PQFP44 |
| 封装： | 1.40 MM HEIGHT, VQFP-44 |
| 文件页数： | 39/74页 |
| 文件大小： | 689K |
| 代理商： | TS80C51RD2-EER |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页
44
Rev. C - 06 March, 2001
TS80C51RA2/RD2
TS83C51RB2/RC2/RD2
TS87C51RB2/RC2/RD2
6.8. Idle mode
An instruction that sets PCON.0 causes that to be the last instruction executed before going into the Idle mode.
In the Idle mode, the internal clock signal is gated off to the CPU, but not to the interrupt, Timer, and Serial Port
functions. The CPU status is preserved in its entirely : the Stack Pointer, Program Counter, Program Status Word,
Accumulator and all other registers maintain their data during Idle. The port pins hold the logical states they had
at the time Idle was activated. ALE and PSEN hold at logic high levels.
There are two ways to terminate the Idle. Activation of any enabled interrupt will cause PCON.0 to be cleared by
hardware, terminating the Idle mode. The interrupt will be serviced, and following RETI the next instruction to
be executed will be the one following the instruction that put the device into idle.
The flag bits GF0 and GF1 can be used to give an indication if an interrupt occured during normal operation or
during an Idle. For example, an instruction that activates Idle can also set one or both flag bits. When Idle is
terminated by an interrupt, the interrupt service routine can examine the flag bits.
The other way of terminating the Idle mode is with a hardware reset. Since the clock oscillator is still running,
the hardware reset needs to be held active for only two machine cycles (24 oscillator periods) to complete the reset.
6.9. Power-Down Mode
To save maximum power, a power-down mode can be invoked by software (Refer to Table 17., PCON register).
In power-down mode, the oscillator is stopped and the instruction that invoked power-down mode is the last
instruction executed. The internal RAM and SFRs retain their value until the power-down mode is terminated.
VCC can be lowered to save further power. Either a hardware reset or an external interrupt can cause an exit from
power-down. To properly terminate power-down, the reset or external interrupt should not be executed before VCC
is restored to its normal operating level and must be held active long enough for the oscillator to restart and stabilize.
Only external interrupts INT0 and INT1 are useful to exit from power-down. For that, interrupt must be enabled
and configured as level or edge sensitive interrupt input.
Holding the pin low restarts the oscillator but bringing the pin high completes the exit as detailed in Figure 17.
When both interrupts are enabled, the oscillator restarts as soon as one of the two inputs is held low and power
down exit will be completed when the first input will be released. In this case the higher priority interrupt service
routine is executed.
Once the interrupt is serviced, the next instruction to be executed after RETI will be the one following the instruction
that put TS80C51Rx2 into power-down mode.
Figure 17. Power-Down Exit Waveform
Exit from power-down by reset redefines all the SFRs, exit from power-down by external interrupt does no affect
the SFRs.
Exit from power-down by either reset or external interrupt does not affect the internal RAM content.
NOTE: If idle mode is activated with power-down mode (IDL and PD bits set), the exit sequence is unchanged, when execution is vectored to interrupt,
PD and IDL bits are cleared and idle mode is not entered.
INT1
INT0
XTAL1
Power-down phase
Oscillator restart phase
Active phase
相关PDF资料 |
PDF描述 |
|---|---|
| TS87C51RB2-LCEB | 8-BIT, OTPROM, 30 MHz, MICROCONTROLLER, PQFP44 |
| TS87C51RD2-EED | 8-BIT, OTPROM, MICROCONTROLLER, PQFP44 |
| TS87C51RD2-MCBB | 8-BIT, OTPROM, 40 MHz, MICROCONTROLLER, PQCC44 |
| TS87C51RD2-VCBB | 8-BIT, OTPROM, 40 MHz, MICROCONTROLLER, PQCC44 |
| TMS320LC542PBK-40 | 16-BIT, 100 MHz, OTHER DSP, PQFP128 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TS80C51RD2-ELB | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| TS80C51RD2-ELD | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| TS80C51RD2-ELR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| TS80C51RD2-EMB | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| TS80C51RD2-EMD | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
发布紧急采购，3分钟左右您将得到回复。