参数资料
型号: TSC80C31-16KAD
厂商: ATMEL CORP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, 16 MHz, MICROCONTROLLER, PDIP40
封装: PLASTIC, DIP-40
文件页数: 38/83页
文件大小: 8336K
代理商: TSC80C31-16KAD
35
8021G–AVR–03/11
ATmega329P/3290P
8.11
Register Description
8.11.1
OSCCAL – Oscillator Calibration Register
Bits 7:0 – CAL7:0: Oscillator Calibration Value
The Oscillator Calibration Register is used to trim the Calibrated Internal RC Oscillator to
remove process variations from the oscillator frequency. A pre-programmed calibration value is
automatically written to this register during chip reset, giving the Factory calibrated frequency as
specified in Table 28-4 on page 335. The application software can write this register to change
the oscillator frequency. The oscillator can be calibrated to frequencies as specified in Table 28-
4 on page 335. Calibration outside that range is not guaranteed.
Note that this oscillator is used to time EEPROM and Flash write accesses, and these write
times will be affected accordingly. If the EEPROM or Flash are written, do not calibrate to more
than 8.8MHz. Otherwise, the EEPROM or Flash write may fail.
The CAL7 bit determines the range of operation for the oscillator. Setting this bit to 0 gives the
lowest frequency range, setting this bit to 1 gives the highest frequency range. The two fre-
quency ranges are overlapping, in other words a setting of OSCCAL = 0x7F gives a higher
frequency than OSCCAL = 0x80.
The CAL6...0 bits are used to tune the frequency within the selected range. A setting of 0x00
gives the lowest frequency in that range, and a setting of 0x7F gives the highest frequency in the
range.
8.11.2
CLKPR – Clock Prescale Register
Bit 7 – CLKPCE: Clock Prescaler Change Enable
The CLKPCE bit must be written to logic one to enable change of the CLKPS bits. The CLKPCE
bit is only updated when the other bits in CLKPR are simultaneously written to zero. CLKPCE is
cleared by hardware four cycles after it is written or when CLKPS bits are written. Rewriting the
CLKPCE bit within this time-out period does neither extend the time-out period, nor clear the
CLKPCE bit.
Bits 3:0 – CLKPS3:0: Clock Prescaler Select Bits 3:0
These bits define the division factor between the selected clock source and the internal system
clock. These bits can be written run-time to vary the clock frequency to suit the application
requirements. As the divider divides the master clock input to the MCU, the speed of all synchro-
nous peripherals is reduced when a division factor is used. The division factors are given in
To avoid unintentional changes of clock frequency, a special write procedure must be followed
to change the CLKPS bits:
Bit
7
65432
10
CAL7
CAL6
CAL5
CAL4
CAL3
CAL2
CAL1
CAL0
OSCCAL
Read/Write
R/W
Initial Value
Device Specific Calibration Value
Bit
7
6
5
4
3210
CLKPCE
CLKPS3
CLKPS2
CLKPS1
CLKPS0
CLKPR
Read/Write
R/W
R
R/W
Initial Value
0
See Bit Description
相关PDF资料
PDF描述
TSC80C31-40JDB 8-BIT, 40 MHz, MICROCONTROLLER, PQFP44
TSC80C31-12LFR 8-BIT, 12 MHz, MICROCONTROLLER, PQFP44
TSC80C31-20LFD 8-BIT, 20 MHz, MICROCONTROLLER, PQFP44
TSC80C31-36KB 8-BIT, 36 MHz, MICROCONTROLLER, PQCC44
TS87C51RD2-VLMR 8-BIT, OTPROM, 40 MHz, MICROCONTROLLER, PQFP64
相关代理商/技术参数
参数描述
TSC80C31-16MA 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:CMOS 0 to 44 MHz Single-Chip 8 Bit Microcontroller
TSC80C31-16MAB/883 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:CMOS 0 to 44 MHz Single-Chip 8 Bit Microcontroller
TSC80C31-16MAD/883 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:CMOS 0 to 44 MHz Single-Chip 8 Bit Microcontroller
TSC80C31-16MAR/883 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:CMOS 0 to 44 MHz Single-Chip 8 Bit Microcontroller
TSC80C31-16MAR/P883 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:CMOS 0 to 44 MHz Single-Chip 8 Bit Microcontroller