- 您现在的位置：买卖IC网 > PDF目录373745 > TSS463D Industrial Control IC PDF资料下载
参数资料
| 型号： | TSS463D |
| 英文描述： | Industrial Control IC |
| 中文描述： | 工业控制IC |
| 文件页数： | 27/52页 |
| 文件大小： | 268K |
| 代理商： | TSS463D |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
TSS461C
27
Rev. D (22 Feb 01)
9.2.7. Last Message Status Register (0x06) :
7
6
5
4
3
2
1
0
NRTR3
NRTR2
NRTR1
NRTR0
IDTR3
IDTR2
IDTR1
IDTR0
Read only register.
Default value after reset : 0x00.
This register is basically the same as the transmission status register. It contains the last identifier number that was
successfully transmitted, received or exceeded its retry count.
If it was a successful transmission, the number of retries performed can be seen in this register as well.
NRTR [3:0]
: Number of retries done successfully in transmission. In case of reception NRTR[3:0] is undefined.
IDTR [3:0]
: Channel number that was successfully transmitted, received or exceeded its retry count.
9.2.8. Last Error Status Register (0x07) :
7
6
5
4
3
2
1
0
BOC
BOV
FCSE
ACKE
CV
FV
Read only register.
Default value after reset : 0
×
00.
The Last Error Status Register contains the error code for the last transmission or reception attempt. It is updated
after each attempt, i.e. several error codes can be reported during one single transmission (with several retries).
BOC
: Buffer occupied.
when one channel configured in
“
Reply request
”
mode has its
“
received
”
bit set when it attempts to transmit its request.
BOC with the link capability between two channels sharing the same
received buffer, is set when one channel has already set its
“
received
”
bit in its
“
Message length and status Channel register
”
and a receive is attempt on the other one.
BOV
: Buffer overflow.
BOV indicates that the buffer length setup in the Channel Status Register
was shorter than the number of bytes received plus 1, and thus, some data
was lost.
One : BOV active
Zero : BOV inactive
FCSE
: Framing Check Sequence Error.
FCSE indicates a mismatch between the FCS received and the FCS
calculated
One : FCSE active
Zero : FCSE inactive
相关PDF资料 |
PDF描述 |
|---|---|
| TSS463R | Industrial Control IC |
| TSS461E | VAN Data Link Controller |
| TSS461E-TDRA-9 | VAN Data Link Controller |
| TSS461E-TERA-9 | VAN Data Link Controller |
| TSS461E-TRDZ-9 | VAN Data Link Controller |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TSS463R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Industrial Control IC |
| TSS463VAN | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:Van Controller Serial Interface |
| TSS47 | 功能描述:瓷片电容器 100V 20% 0.047uF RoHS:否 制造商:Vishay/Cera-Mite 电容:0.01 uF 容差:20 % 电压额定值:3 kV 工作温度范围:- 25 C to + 105 C 损耗因数 DF: 端接类型:Radial 产品:High Voltage Ceramic Disc Capacitors |
| TSS4B01G | 功能描述:整流器 4.0 Amp 50 Volt 150 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 产品:Standard Recovery Rectifiers 配置: 反向电压:100 V 正向电压下降: 恢复时间:1.2 us 正向连续电流:2 A 最大浪涌电流:35 A 反向电流 IR:5 uA 安装风格:SMD/SMT 封装 / 箱体:DO-221AC 封装:Reel |
| TSS4B01G C2 | 制造商:SKMI/Taiwan 功能描述:Diode Rectifier Bridge Single 50V 4A 4-Pin TS4B Tube |
发布紧急采购，3分钟左右您将得到回复。