- 您现在的位置：买卖IC网 > PDF目录98305 > TVP5147M1IPFPQ1 (TEXAS INSTRUMENTS INC) COLOR SIGNAL DECODER, PQFP80 PDF资料下载
参数资料
| 型号： | TVP5147M1IPFPQ1 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 颜色信号转换 |
| 英文描述： | COLOR SIGNAL DECODER, PQFP80 |
| 封装： | PLASTIC, HTQFP-80 |
| 文件页数： | 18/108页 |
| 文件大小： | 937K |
| 代理商： | TVP5147M1IPFPQ1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页
www.ti.com
SLES140F – JULY 2005 – REVISED DECEMBER 2010
2.1.1
Video Input Switch Control
The TVP5147M1 decoder has two analog channels that accept up to ten video inputs. The user can
configure the internal analog video switches via the I2C interface. The ten analog video inputs can be used
for different input configurations, some of which are:
Up to ten selectable individual composite video inputs
Up to four selectable S-video inputs
Up to three selectable analog YPbPr video inputs and one CVBS input
Up to two selectable analog YPbPr video inputs, one S-video input, and two CVBS inputs
The input selection is performed by the input select register at I2C subaddress 00h (see Table 2-12).
2.1.2
Analog Input Clamping
An internal clamping circuit restores the ac-coupled video signal to a fixed dc level. The clamping circuit
provides line-by-line restoration of the video sync level to a fixed dc reference voltage. The selection
between bottom and mid clamp is performed automatically by the TVP5147M1 decoder.
2.1.3
Automatic Gain Control
The TVP5147M1 decoder uses two programmable gain amplifiers (PGAs), one per channel. The PGA can
scale a signal with a voltage-input compliance of 0.5-VPP to 2.0-VPP to a full-scale 10-bit A/D output code
range. A 4-bit code sets the coarse gain with individual adjustment per channel. Minimum gain
corresponds to a code 0x0 (2.0-VPP full-scale input, -6-dB gain) while maximum gain corresponds to code
0xF (0.5 VPP full scale, +6-dB gain). The TVP5147M1 decoder also has 12-bit fine gain controls for each
channel and applies independently to coarse gain controls. For composite video, the input video signal
amplitude can vary significantly from the nominal level of 1 VPP. The TVP5147M1 decoder can adjust its
PGA setting automatically: an automatic gain control (AGC) can be enabled and can adjust the signal
amplitude such that the maximum range of the ADC is reached without clipping. Some nonstandard video
signals contain peak white levels that saturate the ADC. In these cases, the AGC automatically cuts back
gain to avoid clipping. If the AGC is on, then the TVP5147M1 decoder can read the gain currently being
used.
The TVP5147M1 AGC comprises the front-end AGC before Y/C separation and the back-end AGC after
Y/C separation. The back-end AGC restores the optimum system gain whenever an amplitude reference
such as the composite peak (which is only relevant before Y/C separation) forces the front-end AGC to set
the gain too low. The front-end and back-end AGC algorithms can use up to four amplitude references:
sync height, color burst amplitude, composite peak, and luma peak.
The specific amplitude references being used by the front-end and back-end AGC algorithms can be
independently controlled using the AGC white peak processing register located at subaddress 74h. The
TVP5147M1 gain increment speed and gain increment delay can be controlled using the AGC increment
speed register located at subaddress 78h and the AGC increment delay register located at subaddress
79h.
2.1.4
Analog Video Output
One of the analog input signals is available at the analog video output terminal, which is shared with input
selected by I2C registers. The signal at this terminal must be buffered by a source follower. The nominal
output voltage is 2 V p-p, thus the signal can be used to drive a 75-
Ω line. The magnitude is maintained
with an AGC in 16 steps controlled by the TVP5147M1 decoder. To use this function, terminal VI_1_A
must be set as an output terminal. The input mode selection register also selects an active analog output
signal.
Copyright 2005–2010, Texas Instruments Incorporated
Functional Description
17
Product Folder Link(s): TVP5147M1
相关PDF资料 |
PDF描述 |
|---|---|
| TVP5147PFPG4 | COLOR SIGNAL DECODER, PQFP80 |
| TVP5147PFP | COLOR SIGNAL DECODER, PQFP80 |
| TVP5147PFPR | COLOR SIGNAL DECODER, PQFP80 |
| TVP5147PFPRG4 | COLOR SIGNAL DECODER, PQFP80 |
| TVP5150AM1MPBSREP | COLOR SIGNAL DECODER, PQFP32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TVP5147M1IPFPR | 功能描述:视频 IC 10B Hi Qual Sgl-Chip Dig Video Decoder RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel |
| TVP5147M1PFP | 功能描述:视频 IC 10B High Qual S-Chip Dig Vid Decoder RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel |
| TVP5147M1PFP | 制造商:Texas Instruments 功能描述:; Resolution (Bits):10; Supply Current:5 |
| TVP5147M1PFP_07 | 制造商:TI 制造商全称:Texas Instruments 功能描述:NTSC/PAL/SECAM 2 X 10-Bit Digital Video Decoder With Macrovision Detection, YPbPr Inputs, and 5-Line Comb Filter |
| TVP5147M1PFPG4 | 制造商:TI 制造商全称:Texas Instruments 功能描述:NTSC/PAL/SECAM 2 X 10-Bit Digital Video Decoder With Macrovision Detection, YPbPr Inputs, and 5-Line Comb Filter |
发布紧急采购，3分钟左右您将得到回复。