- 您现在的位置：买卖IC网 > PDF目录18805 > TXM-916-ES_ (Linx Technologies Inc)TRANSMITTER RF 916MHZ 10PIN SMD PDF资料下载
参数资料
| 型号： | TXM-916-ES_ |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 4/11页 |
| 文件大小： | 0K |
| 描述： | TRANSMITTER RF 916MHZ 10PIN SMD |
| 产品变化通告： | ES Series Frequency Change 22/Dec/2010 |
| 产品目录绘图： | TXM-916-ES Top TXM-916-ES Side |
| 标准包装： | 40 |
| 系列： | ES |
| 频率： | 916MHz |
| 应用： | 住宅/楼宇自动化，工业控制和监控 |
| 调制或协议： | AM，OOK |
| 数据传输率 - 最大： | 56 kbps |
| 功率 - 输出： | 4dBm |
| 电流 - 传输： | 8.5mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 电源电压： | 2.1 V ~ 4 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 模块 |
| 包装： | 散装 |
| 其它名称： | TXM-916-ES TXM-916-ES_-ND TXM916ES |
USING THE DIVIDED CLOCK OUTPUT (/CLK)
When the ES is used with a microcontroller, the divided clock output (/CLK)
saves cost and space by eliminating the need for a crystal or other frequency
reference for the microprocessor. This line is an open collector output, so an
external pull-up resistor (R L ) should be connected between this line and the
positive supply voltage. The value of R L is calculated using two factors:
1) Determine the clock frequency (f CLKOUT ). If /CLK SE is open, the /CLK output
will be the Tx center frequency (in MHz) divided by 1,024; if /CLK SEL is
grounded, it will be /256.
2) Determine the load capacitance of the PCB plus the microcontroller’s input
capacitance (C LD in pF).
Using these two factors, the value of R L can be easily calculated:
USING THE PDN PIN
The Power Down (PDN) line can be used to power down the transmitter without
the need for an external switch. This line has an internal pull-up, so when it is
held high or simply left floating, the module will be active.
When the PDN line is pulled to ground, the transmitter will enter into a low-
current (<95μA) power-down mode. During this time, the transmitter is off and
cannot perform any function. The startup time coming out of power-down will be
the same as applying V CC .
The PDN line allows easy control of the transmitter state from external
components, such as a microcontroller. By periodically activating the transmitter,
sending data, then powering down, the transmitter’s average current
consumption can be greatly reduced, saving power in battery operated
applications.
“/256” R L = 1000/(f CLKOUT *8*C LD )
“/1024” R L = 1000/(f CLKOUT *8*C LD )
USING THE LO_V_D PIN
Example: Example:
For /256: 1000/((916.48/256)x8x5)=6.98k Ω For /1024: 1000/((916.48/1024)x8x5)=27.9k Ω
USING LADJ
The transmitter’s output power can be externally adjusted by approximately
-65dBm using the LADJ line. This eliminates the need for external attenuation
and allows the transmitter’s power to be easily adjusted for range control, lower
power consumption, or to meet legal requirements. This line can also be
modulated to allow the ES to operate as an AM transmitter; however, this is not
recommended since the ES receiver is designed only for FM / FSK recovery and
the performance and noise immunity advantages of FM would be lost.
When the LADJ line is open, the output power will be at its maximum and the
transmitter will draw 7mA typically. When LADJ is at 0V, the output power will be
at its minimum and the transmitter will draw 3mA typically.
To set the transmit power at a particular level, simply create a voltage reference
at the LADJ line at an appropriate level to achieve the desired output power. The
easiest way to accomplish this is with an appropriate value resistor from the
In many instances, the transmitter may be employed in a battery-powered
device. In such applications, it is often useful to be able to sense a low-battery
condition, either to signal the need for battery replacement or to power down
components that might otherwise operate unpredictably. Normally, this
supervisory function would require additional circuitry, but the ES Series
transmitter includes the function on-board.
The Low Voltage Detect line (LO_V_D) will transition low when the supply
voltage to the transmitter falls below a typical threshold of 2.15VDC. This output
can be tied directly to the module’s PDN line to shut off the transmitter, or used
to indicate the low voltage condition to an external circuit or microprocessor. The
output could also be used to provide a visual indication of the low power
condition via a LED, although a buffer transistor would generally be required to
provide an adequate drive level.
The output can also be monitored in applications with a power supply as a
safeguard against brownout conditions.
POWER SUPPLY REQUIREMENTS
LADJ line to ground. This resistor works in combination with the internal supply
pull-up to create a voltage divider. Page 3 of this data guide features a chart
The module does not have an internal voltage
regulator; therefore it requires a clean, well-regulated
Vcc TO
MODULE
showing typical resistor values and corresponding attenuation levels.
The LADJ line is very useful during FCC testing to compensate for antenna gain
or other product-specific issues that may cause the output power to exceed legal
limits. Often it is wise to connect the LADJ line to a variable resistor so that the
power source. While it is preferable to power the unit
from a battery, it can also be operated from a power
supply as long as noise is less than 20mV. Power
supply noise can affect the transmitter modulation;
Vcc IN
10 Ω
10 μ F
A 10 Ω resistor in series with the supply followed by a
test lab can precisely adjust the output power to the maximum threshold allowed
by law. The resistor’s value can then be noted and a fixed resistor substituted for
final testing. Even in designs where attenuation is not anticipated, it is a good
idea to place a resistor pad connected to LADJ so that it can be used if needed.
For more sophisticated designs, LADJ may also be controlled by a DAC or digital
potentiometer to allow precise and digitally variable output power control.
In any case where the voltage on the LADJ line may fall below 1.5VDC, a low-
value ceramic capacitor (200 to 4,700pF) must be placed from the module’s
power supply to the LADJ pin. This is necessary to meet the module’s minimum
enable voltage at start-up.
Page 6
therefore, providing a clean power supply for the
module should be a high priority during design.
Figure 9: Supply Filter
10μF tantalum capacitor from V CC to ground will help in cases where the quality
of supply power is poor. Note that operation from 4.3 to 5.2 volts requires the
use of an external 270 Ω resistor placed in series with the supply to prevent V CC
from exceeding 4.0 volts, so the dropping resistor can take the place of the 10 Ω
resistor in the supply filter. These values may need to be adjusted depending on
the noise present on the supply line.
Page 7
相关PDF资料 |
PDF描述 |
|---|---|
| R9G22612CSOO | RECTIFIER FAST REC 2600V 1200A |
| D2VW-01-3HS | MINIATURE BASIC SWITCH |
| 601W-36-S | LEAD TEST MINIHK-BANAPLG SET/10 |
| FXO-HC736R-45.1584 | OSC 45.1584 MHZ 3.3V HCMOS SMD |
| 681-36-S | LEAD TEST ALLIGCLP-BANAPLG SET10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TXM-916-ES_ | 功能描述:TRANSMITTER RF 916MHZ 10PIN SMD RoHS:是 类别:RF/IF 和 RFID >> RF 发射器 系列:ES 标准包装:4,000 系列:- 频率:310MHz ~ 440MHz 应用:- 调制或协议:UHF，ASK 数据传输率 - 最大:20 kBaud 功率 - 输出:1dBm ~ 5dBm 电流 - 传输:10mA 数据接口:PCB，表面贴装 天线连接器:PCB，表面贴装 存储容量:- 特点:- 电源电压:2.2 V ~ 4 V 工作温度:-40°C ~ 85°C 封装/外壳:16-LSSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| TX-MVX | 制造商:Radio Design Labs 功能描述:Two Bnc In, Single Bnc Out Manual Video Switch 制造商:RADIO DESIGN LABS 功能描述:MANUAL VIDEO SWITCH TWO BNC IN, SINGLE BNC OUT |
| TX-MX2R | 制造商:Radio Design Labs 功能描述:Mixer /Distribution Amplifier 制造商:RADIO DESIGN LABS 功能描述:MIXER /DISTRIBUTION AMPLIFIER |
| TXN/A10NCSS | 制造商:Panasonic Industrial Company 功能描述:PC BOARD |
| TXN/A10QBMS | 制造商:Panasonic Industrial Company 功能描述:PC BOARD |
发布紧急采购，3分钟左右您将得到回复。