参数资料
| 型号： | TZA1038HW,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 6/45页 |
| 文件大小： | 0K |
| 描述： | IC DVD SIGNAL PROC 48-HTQFP |
| 标准包装： | 2,500 |
| 系列： | * |
| 类型： | * |
| 应用： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-TQFP 裸露焊盘 |
| 供应商设备封装： | 48-HTQFP |
| 包装： | 带卷 (TR) |
| 其它名称： | 935273843118 TZA1038HW-T TZA1038HW-T-ND |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
2003 Sep 03
14
Philips Semiconductors
Product specication
High speed advanced analog DVD signal
processor and laser supply
TZA1038HW
7.2.5
AUTOMATIC DUAL LASER SUPPLY
The TZA1038HW can control the output power of two
lasers; it has an Automatic Laser Power Control (ALPC)
that stabilizes the laser output power and compensates
the effects of temperature and ageing of the laser.
ALPC automatically detects if there is a P-type or N-type
monitor diode in use in either of the laser circuits. The
regulation loop formed by the ALPC, the laser, the monitor
diode and the associated adjustment resistor will settle at
the monitor input voltage. The monitor input voltage can be
programmed to HIGH (
≈ 180 mV) or LOW (≈ 150 mV),
according to frequently-used pre-adjustments of the light
pen. This set point can be set independently for both
ALPCs. Bandwidth limitation and smooth switch-on
behaviour is realized using an internal capacitor.
A protection circuit is included to prevent laser damage
due to dips in laser supply voltage VDDL. If a supply voltage
dip occurs, the output can saturate and restrict the
required laser current. Without the protection circuit, the
ALPC would try to maximize the output power with
destructive results for the laser when the supply voltage
recovers. The protection circuit monitors the supply
voltage and shuts off the laser when the voltage drops
below a safe value. The ALPC recovers automatically after
the dip has passed.
Only one laser can be activated at the same time.
An internal break-before-make circuit ensures safe
start-up for the laser when a toggle situation between the
two lasers is detected. When both lasers are programmed
on, neither laser will be activated.
7.2.6
POWER-ON RESET AND GENERAL POWER ON
When the supply voltage is switched on, bit PWRON is
reset by the Power-On Reset (POR) signal. This
concludes in a STANDBY mode at power up. POR is
intended to prevent the lasers being damaged due to
random settings. All other functions may be switched when
power is on. The TZA1038HW becomes active when
bit PWRON = 1.
7.2.7
COMPATIBILITY WITH TZA1033HL/V1
7.2.7.1
Software compatibility
The TZA1038HW is highly software compatible with the
TZA1033HL/V1. Provided that some conditions are met,
the software of the TZA1038HW can be used as a
successor with just minor modifications. This compatibility
is achieved with the implementation of the TZA1038HW
mode control bit (bit K2_Mode). When bit K2_Mode = 0,
the TZA1038HW will act as a TZA1033HL/V1. When
bit K2_Mode = 1, the TZA1038HW will act as a
TZA1033HL/K2 and the new functions will be available
(but require a software update).
Other conditions or restrictions are:
Register bits of the TZA1038HW which were not defined
are programmed to a logic 0. Registers 9, 10, 14 and 15
may be left undefined
The G4 stage high gain setting of the TZA1033HL/V1 is
not available in the TZA1038HW; if this value was set to
logic 0, there will be no difference
When bit K2_Mode = 0 the RF bandwidth will be fixed to
the minimum value of 10 MHz (typical); bit K2_Mode = 1
to select a higher bandwidth; the bandwidth is now lower
than using a TZA1033HL/V1.
7.2.7.2
Hardware compatibility
The package is changed from LQFP64 for the TZA1033HL
to LQFP48 for the TZA1038HW.
The hardware differences are:
Input pins STB, HEADER and LAND of the TZA1033HL
are not present
Input pins CD of TZA1033HL/V1 are not used;
TZA1038HW has RFSUM inputs instead; the RFSUM
inputs of TZA1038HW may be connected to ground
when not used.
相关PDF资料 |
PDF描述 |
|---|---|
| UG80960HD5016SL2GM | IC MPU I960HD 3V 50MHZ 208-QFP |
| ULQ2003ATDG4Q1 | IC DARLINGTON TRANS ARRAY 16SOIC |
| UPD70F3025AGC-33-8EU-A | MCU 32BIT 256K FLASH 100LQFP |
| UPD70F3201YGC-YEU-A | MCU 32BIT I2C 100TQFP |
| UPD70F3452GC-UBT-A | MCU 32BIT 256KB FLASH 80LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TZA1038HW-T | 功能描述:音频 DSP DVDALASLITE AUTO RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
| TZ-A103SS | 制造商:Panasonic Industrial Company 功能描述:SIGNAL SENDER |
| TZA1045 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Photodiode and amplifier IC for CD and DVD applications |
| TZA1045TS | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Photodiode and amplifier IC for CD and DVD applications |
| TZA1046 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Photodiode and amplifier IC for CD and DVD applications |
发布紧急采购，3分钟左右您将得到回复。