- 您现在的位置：买卖IC网 > PDF目录1882 > UBA2015P/1,112 (NXP Semiconductors)IC LAMP DVR FLUORES 600V 20-DIP PDF资料下载
参数资料
| 型号： | UBA2015P/1,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 18/42页 |
| 文件大小： | 0K |
| 描述： | IC LAMP DVR FLUORES 600V 20-DIP |
| 标准包装： | 20 |
| 类型： | CFL/TL 驱动器 |
| 电流 - 电源： | 1.7mA |
| 电源电压： | 11.9 V ~ 13.8 V |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 20-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 20-DIP |
| 包装： | 管件 |
| 其它名称： | UBA2015P1112 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
NXP Semiconductors
UBA2016A/15/15A
600 V fluorescent lamp driver
The amount of boost depends on the current into the BOOST pin and the lamp current
control. If the application does not use lamp current control, the switching frequency will
go down to the lowest possible boost switching frequency f sw(bst)(low) (point G in Figure 11
Equation 2 , depending on the value of I BOOST .
0 ? I BOOST ? I sat ? BOOST ? ? f sw ? bst ? ? low ? = f sw ? low ? ? 1 – I BOOST ? N f ? bst ? ? low ? ?
I BOOST ? I sat ? BOOST ? ? f sw ? bst ? ? low ? = f sw ? low ? ? 1 – I sat ? BOOST ? ? N f ? bst ? ? low ? ?
(1)
(2)
If the application uses lamp current control, the switching frequency is regulated to boost
(depending on the value of I BOOST ) if the switching frequency remains above f sw(bst)(low) ,
otherwise the switching frequency is f sw(bst)(low) ; see Equation 1 or Equation 2 .
0 ? I BOOST ? I sat ? BOOST ? ? V reg ? IFB ? ? I BOOST ? = V reg ? IFB ? ? 1 + I BOOST ? N l ? bst ? reg ?
I BOOST ? I sat ? BOOST ? ? V reg ? bst ? ? IFB ? = V reg ? IFB ? + I sat ? BOOST ? ? N Vreg ? bst ?
(3)
(4)
7.4.8 Stop state
When in Stop state the IC is off and all driver outputs are low. The IC will remain in Stop
state until the voltage on pin VDD drops below V rst(VDD) or it is disabled, in which case it
will go to Reset state.
7.5 Enable and Disable
The enable function is only available in the UBA2015 and UBA2015A and works via pin
PH/EN. If this pin is pulled below the enable voltage V en(PH/EN) then the IC goes into the
Standby state (immediately if GLHB is high, otherwise it will continue its normal clock
cycle until GLHB is high and then go to the Standby state).
The external interface with pin PH/EN for the enable signal should be an open collector or
open drain type driver. To enable the IC the open collector or open drain should be open
(high ohmic) to not disturb the fixed frequency preheat setting function of pin PH/EN.
In Restart, Standby and Stop states the standby pull-up current source I pu(stb)(PH/EN) will
pull the voltage at pin PH/EN above V en(PH/EN) . In Preheat, Ignition and Burn states the
normal output voltage driver of the IC will pull the pin high. In those cases the external
driver must draw a current I clamp(PH/EN) from the pin to disable the IC.
7.6 Protection circuits
7.6.1 End-of-life rectifying lamp detection
If voltage on pin EOL is below low threshold voltage V th(low)EOL or above V th(high)EOL the
fault timer will start. These threshold voltage levels are related to pin FBPFC voltage
according to the formula: V th(low)EOL = V FBPFC = V th(high)EOL / 2. The FBPFC voltage is
sampled during GPFC low and hold during GPFC high periods to prevent disturbance of
the EOL levels due to the switching of the PFC.
UBA2016A_15_15A
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 16 November 2011
? NXP B.V. 2011. All rights reserved.
18 of 42
相关PDF资料 |
PDF描述 |
|---|---|
| UBA2024AP/N1,112 | IC DRIVER HALF BRIDGE 8-DIP |
| UBA2035TS/N1,118 | IC DVR HF FULL BRIDGE 28-SSOP |
| UBA2036TS/N1,118 | IC DVR FULL BRIDGE 28-SSOP |
| UBA2037TS/N1,118 | IC DVR FULL BRIDGE 28-SSOP |
| UBA2070T/N1,518 | IC CCFL DRIVER 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UBA2015PN1 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:600 V fluorescent lamp driver with PFC, linear dimming and boost function |
| UBA2015T | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:600 V fluorescent lamp driver with PFC, linear dimming and boost function |
| UBA2015T/1 | 制造商:NXP Semiconductors 功能描述:HFTL CNTRL PFC FPH SO20 制造商:NXP Semiconductors 功能描述:HFTL CNTRL, PFC, FPH, SO20 |
| UBA2015T/1,118 | 功能描述:显示驱动器和控制器 600V 0.16mA SO20 RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| UBA2015TN1 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:600 V fluorescent lamp driver with PFC, linear dimming and boost function |
发布紧急采购，3分钟左右您将得到回复。