参数资料
型号: UM232R
厂商: FTDI, Future Technology Devices International Ltd
文件页数: 20/28页
文件大小: 0K
描述: MOD USB UART DEV FT232R
产品培训模块: USB Introduction
USB-UART Interface Solutions
产品目录绘图: UM232R
标准包装: 5
主要目的: 接口,USB 2.0 至 UART(RS232)电桥
嵌入式:
已用 IC / 零件: FT232R
主要属性: 全速,300 ~ 3 MB 速率,安全识别号
次要属性: 6 ~ 48MHz 时钟发生器输出,免版税驱动器
已供物品:
产品目录页面: 633 (CN2011-ZH PDF)
相关产品: 768-1008-6-ND - IC USB FS SERIAL UART 32-QFN
768-1007-6-ND - IC USB FS SERIAL UART 28-SSOP
768-1008-1-ND - IC USB FS SERIAL UART 32-QFN
768-1007-1-ND - IC USB FS SERIAL UART 28-SSOP
768-1008-2-ND - IC USB FS SERIAL UART 32-QFN
768-1007-2-ND - IC USB FS SERIAL UART 28-SSOP
其它名称: 768-1019
Document Reference No.: FT_000051
UM232R USB - Serial UART Development Module
Datasheet Version 1.1
Clearance No.: FTDI# 125
7.3 USB Bus Powered with Power Switching Confiduration
P-Channel Power
MOSFET
s
d
UM232R ? FTDI 2008
0.1uF
0.1uF
TXD
1
J1
1
2
3
24
g
Soft
Start
TXD
Circuit
RXD
RTS#
RTS# 3
1K
MCU
CTS#
RXD
5
GND
7
18
CB3
(PWREN#)
CTS#
10
12
J2
2
1
14
13
USB
Figure 7.3 Bus Powered with Power Switching Configuration
USB Bus Powered circuits need to be able to power down in USB suspend mode in order to meet the
<=500μA total USB suspend current requirement (including external logic). Some external can power itself
down into a low current state by monitoring the PWREN# signal. For external logic that cannot power itself
down in this way the FT232R provides a simple but effective way of turning off power to external circuitry
during USB suspend.
Figure 7.3 shows how to use a discrete P-Channel Logic Level MOSFET to control the power to external logic
circuits. A suitable device would be an International Rectifier ( www.irf.com ) IRLML6402, or equivalent. It is
recommended that a “soft start” circuit consisting of a 1kΩseries resistor and a 0.1μF capacitor are used to
limit the current surge when the MOSFET turns on. Without the soft start circuit there is a danger that the
transient power surge of the MOSFET turning on will reset the FT232R, or the USB host / hub controller.
The values used here allow attached circuitry to power up with a slew rate of ~12.5V per millisecond, in
other words the output voltage will transition from GND to 5V in approximately 400 microseconds.
Alternatively, a dedicated power switch I.C. with inbuilt “soft - start” can be used instead of a MOSFET. A
suitable power switch I.C. for such an application would be a Micrel ( www.micrel.com ) MIC2025-2BM or
equivalent.
Please note the following points in connection with power controlled designs:
i) The logic to be controlled must have its own reset circuitry so that it will automatically reset itself
when power is applied on coming out of suspend.
ii) Set the Pull-down on Suspend option in the internal EEPROM.
iii) One of the CBUS Pins should be configured as PWE# in the internal EEPROM, and should be used to
switch the power supply to the external circuitry.
iv)
For USB high-power bus powered device (one that consumes greater than 100mA, and up to 500mA
of current from the USB bus), the power consumption of the device should be set in the max power
field in the internal EEPROM. A high-power bus powered device must use this descriptor in the
internal EEPROM to inform the system of its power requirements.
? Copyright 2005-2011 Future Technology Devices International Ltd
19
相关PDF资料
PDF描述
UM245R MOD USB PARALLEL FIFO DEV FT245R
UMTS 2 FUSE 2A 250V TLAG IEC SMD
UPG1-4-61-303-01 MAGNETIC CIRC BRKR SP 30A TOG SW
UPL111-1-60-503 MAGNETIC CIRCUIT PROTECTOR 50A
UPL2000-D1/B BNC PLUG CRIMP STR 7538CBL 50/PK
相关代理商/技术参数
参数描述
UM233 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC
UM233M 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC
UM234 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC
UM2341 制造商:Coto Technology 功能描述:Reed Switch 制造商:Coto Technology 功能描述:SWITCH, REED, SPST, 500mA, 175VDC, Contact Configuration:SPST, Switching Voltage
UM234M 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC