- 您现在的位置：买卖IC网 > PDF目录1971 > UPD70F3025AGC-33-8EU-A (Renesas Electronics America)MCU 32BIT 256K FLASH 100LQFP PDF资料下载
参数资料
| 型号： | UPD70F3025AGC-33-8EU-A |
| 厂商： | Renesas Electronics America |
| 文件页数： | 16/49页 |
| 文件大小： | 0K |
| 描述： | MCU 32BIT 256K FLASH 100LQFP |
| 标准包装： | 50 |
| 系列： | V853 |
| 核心处理器： | V850ES |
| 芯体尺寸： | 32-位 |
| 速度： | 33MHz |
| 连通性： | CSI，EBI/EMI，UART/USART |
| 外围设备： | PWM |
| 输入/输出数： | 67 |
| 程序存储器容量： | 256KB（256K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 8K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 数据转换器： | A/D 8x10b，D/A 2x8b |
| 振荡器型： | 外部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-LQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
2011 Microchip Technology Inc.
DS31037B-page 23
PIC24F16KL402 FAMILY
2.4
ICSP Pins
The PGC and PGD pins are used for In-Circuit Serial
Programming (ICSP) and debugging purposes. It
is recommended to keep the trace length between the
ICSP connector and the ICSP pins on the device as
short as possible. If the ICSP connector is expected to
experience an ESD event, a series resistor is recom-
mended, with the value in the range of a few tens of
ohms, not to exceed 100.
Pull-up resistors, series diodes and capacitors on the
PGC and PGD pins are not recommended as they will
interfere with the programmer/debugger communica-
tions to the device. If such discrete components are an
application requirement, they should be removed from
the circuit during programming and debugging. Alter-
natively, refer to the AC/DC characteristics and timing
requirements information in the respective device
Flash programming specification for information on
capacitive loading limits, and pin input voltage high
(VIH) and input low (VIL) requirements.
For device emulation, ensure that the “Communication
Channel Select” (i.e., PGCx/PGDx pins), programmed
into the device, matches the physical connections for
the ICSP to the Microchip debugger/emulator tool.
For
more
information
on
available
Microchip
development tools connection requirements, refer to
.
2.5
External Oscillator Pins
Many microcontrollers have options for at least two
oscillators: a high-frequency primary oscillator and a
low-frequency
secondary
oscillator
(refer
to
for details).
The oscillator circuit should be placed on the same
side of the board as the device. Place the oscillator
circuit close to the respective oscillator pins with no
more than 0.5 inch (12 mm) between the circuit
components and the pins. The load capacitors should
be placed next to the oscillator itself, on the same side
of the board.
Use a grounded copper pour around the oscillator cir-
cuit to isolate it from surrounding circuits. The
grounded copper pour should be routed directly to the
MCU ground. Do not run any signal traces or power
traces inside the ground pour. Also, if using a two-sided
board, avoid any traces on the other side of the board
where the crystal is placed.
Layout suggestions are shown in Figure 2-3. In-line
packages may be handled with a single-sided layout
that completely encompasses the oscillator pins. With
fine-pitch packages, it is not always possible to com-
pletely surround the pins and components. A suitable
solution is to tie the broken guard sections to a mirrored
ground layer. In all cases, the guard trace(s) must be
returned to ground.
FIGURE 2-3:
SUGGESTED PLACEMENT
OF THE OSCILLATOR
CIRCUIT
In planning the application’s routing and I/O assign-
ments, ensure that adjacent port pins and other
signals, in close proximity to the oscillator, are benign
(i.e., free of high frequencies, short rise and fall times,
and other similar noise).
GND
`
OSC1
OSC2
T1OSO
T1OS I
Copper Pour
Primary Oscillator
Crystal
Timer1 Oscillator
Crystal
DEVICE PINS
Primary
Oscillator
C1
C2
T1 Oscillator: C1
T1 Oscillator: C2
(tied to ground)
Single-Sided and In-Line Layouts:
Fine-Pitch (Dual-Sided) Layouts:
GND
OSCO
OSCI
Bottom Layer
Copper Pour
Oscillator
Crystal
Top Layer Copper Pour
C2
C1
DEVICE PINS
(tied to ground)
相关PDF资料 |
PDF描述 |
|---|---|
| UPD70F3201YGC-YEU-A | MCU 32BIT I2C 100TQFP |
| UPD70F3452GC-UBT-A | MCU 32BIT 256KB FLASH 80LQFP |
| UPD70F3714GC-8BS-A | MCU 32BIT V850ES/LX2 64-LQFP |
| UPD70F3757GJ-GAE-AX | MCU 32BIT V850ES/HX3 144-LQFP |
| UPD720101GJ-UEN-A | HOST CTLR USB 2.0 144-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UPD70F3030B | 制造商:未知厂家 制造商全称:未知厂家 功能描述:V850 Series Pamphlet | Pamphlet[02/2002] |
| UPD70F3030BY | 制造商:未知厂家 制造商全称:未知厂家 功能描述:V850/SB1(TM).V850/SB2(TM) for Hardware | UM Including Electrical Characteristics[02/2003] |
| UPD70F3032A | 制造商:未知厂家 制造商全称:未知厂家 功能描述:The RISC power shapes your imagination Pamphlet | Pamphlet[05/2002] |
| UPD70F3032AY | 制造商:未知厂家 制造商全称:未知厂家 功能描述:V850 Family(TM) for Architecture | User＇s Manual[03/2001] |
| UPD70F3032B | 制造商:未知厂家 制造商全称:未知厂家 功能描述:V850 Series Pamphlet | Pamphlet[02/2002] |
发布紧急采购，3分钟左右您将得到回复。