参数资料
型号: UPD78F9234MC-5A4-A
厂商: Renesas Electronics America
文件页数: 343/419页
文件大小: 0K
描述: MCU 8BIT 8KB FLASH 30PIN
标准包装: 400
系列: 78K0S/Kx1+
核心处理器: 78K0S
芯体尺寸: 8-位
速度: 10MHz
连通性: LIN,UART/USART
外围设备: LVD,POR,PWM,WDT
输入/输出数: 24
程序存储器容量: 8KB(8K x 8)
程序存储器类型: 闪存
RAM 容量: 256 x 8
电压 - 电源 (Vcc/Vdd): 2 V ~ 5.5 V
数据转换器: A/D 4x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 30-LSSOP(0.240",6.10mm 宽)
包装: 托盘
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页第202页第203页第204页第205页第206页第207页第208页第209页第210页第211页第212页第213页第214页第215页第216页第217页第218页第219页第220页第221页第222页第223页第224页第225页第226页第227页第228页第229页第230页第231页第232页第233页第234页第235页第236页第237页第238页第239页第240页第241页第242页第243页第244页第245页第246页第247页第248页第249页第250页第251页第252页第253页第254页第255页第256页第257页第258页第259页第260页第261页第262页第263页第264页第265页第266页第267页第268页第269页第270页第271页第272页第273页第274页第275页第276页第277页第278页第279页第280页第281页第282页第283页第284页第285页第286页第287页第288页第289页第290页第291页第292页第293页第294页第295页第296页第297页第298页第299页第300页第301页第302页第303页第304页第305页第306页第307页第308页第309页第310页第311页第312页第313页第314页第315页第316页第317页第318页第319页第320页第321页第322页第323页第324页第325页第326页第327页第328页第329页第330页第331页第332页第333页第334页第335页第336页第337页第338页第339页第340页第341页第342页当前第343页第344页第345页第346页第347页第348页第349页第350页第351页第352页第353页第354页第355页第356页第357页第358页第359页第360页第361页第362页第363页第364页第365页第366页第367页第368页第369页第370页第371页第372页第373页第374页第375页第376页第377页第378页第379页第380页第381页第382页第383页第384页第385页第386页第387页第388页第389页第390页第391页第392页第393页第394页第395页第396页第397页第398页第399页第400页第401页第402页第403页第404页第405页第406页第407页第408页第409页第410页第411页第412页第413页第414页第415页第416页第417页第418页第419页
APPENDIX D LIST OF CAUTIONS
User’s Manual U17446EJ5V0UD
405
(16/20)
Chapter
Cl
assi
fi
cati
on
Function
Details of
Function
Cautions
Page
<1> must always be executed. When LVIMK = 0, an interrupt may occur
immediately after the processing in <3>.
p.263
When used as
reset
If supply voltage (VDD)
≥ detection voltage (VLVI) when LVIM is set to 1, an
internal reset signal is not generated.
p.263
Chapter
1
7
Soft
Low-
voltage
detector
Cautions for low-
voltage detector
In a system where the supply voltage (VDD) fluctuates for a certain period in
the vicinity of the LVI detection voltage (VLVI), the operation is as follows
depending on how the low-voltage detector is used.
<1> When used as reset
The system may be repeatedly reset and released from the reset status.
In this case, the time from release of reset to the start of the operation of the
microcontroller can be arbitrarily set by taking action (1) below.
<2> When used as interrupt
Interrupt requests may be frequently generated. Take action (2) below.
p.266
Oscillation
stabilization time
on power
application or
after reset
release
The setting of this option is valid only when the crystal/ceramic oscillation clock
is selected as the system clock source. No wait time elapses if the high-speed
internal oscillation clock or external clock input is selected as the system clock
source.
p.270
Control of
RESET pin
Because the option byte is referenced after reset release, if a low level is input
to the RESET pin before the option byte is referenced, then the reset state is
not released.
Also, when setting 0 to RMCE, connect the pull-up resistor.
p.270
Selection of
system clock
source
Because the X1 and X2 pins are also used as the P121 and P122 pins, the
conditions under which the X1 and X2 pins can be used differ depending on
the selected system clock source.
(1) Crystal/ceramic oscillation clock is selected
The X1 and X2 pins cannot be used as I/O port pins because they are used
as clock input pins.
(2) External clock input is selected
Because the X1 pin is used as an external clock input pin, P121 cannot be
used as an I/O port pin.
(3) High-speed internal oscillation clock is selected
P121 and P122 can be used as I/O port pins.
p.270
If it is selected that low-speed internal oscillator cannot be stopped, the count
clock to the watchdog timer (WDT) is fixed to low-speed internal oscillation
clock.
p.271
Chapter
1
8
Hard
Option byte
Low-speed
internal oscillates
If it is selected that low-speed internal oscillator can be stopped by software,
supply of the count clock to WDT is stopped in the HALT/STOP mode,
regardless of the setting of bit 0 (LSRSTOP) of the low-speed internal
oscillation mode register (LSRCM). Similarly, clock supply is also stopped
when a clock other than the low-speed internal oscillation clock is selected as
a count clock to WDT.
While the low-speed internal oscillator is operating (LSRSTOP = 0), the clock
can be supplied to the 8-bit timer H1 even in the STOP mode.
p.271
相关PDF资料
PDF描述
UPD78F9232MC-5A4-A MCU 8BIT 4KB FLASH 30PIN
VI-BNJ-IX-F4 CONVERTER MOD DC/DC 36V 75W
C8051F824-GS IC MCU 8BIT 8KB FLASH 16SOIC
VI-BNJ-IX-F2 CONVERTER MOD DC/DC 36V 75W
VI-BNJ-IX-F1 CONVERTER MOD DC/DC 36V 75W
相关代理商/技术参数
参数描述
UPD78F9306GC-8BS-A 制造商:Renesas Electronics Corporation 功能描述:
UPD78F9306GK-9ET 制造商:Renesas Electronics Corporation 功能描述:
UPD78F9306GK-9ET-A 制造商:Renesas Electronics Corporation 功能描述:
UPD78F9316GK-9ET-A 制造商:Renesas Electronics Corporation 功能描述:MCU 8-bit 78K 78K0 CISC 16KB Flash 2.5V/3.3V/5V 64-Pin TQFP
UPD78F9316GK-9ETA-A 制造商:Renesas Electronics Corporation 功能描述: