- 您现在的位置：买卖IC网 > PDF目录18814 > US1881LUA-AAA-000-BU (Melexis Technologies NV)IC LATCH CMOS MP TO-92UA PDF资料下载
参数资料
| 型号： | US1881LUA-AAA-000-BU |
| 厂商： | Melexis Technologies NV |
| 文件页数： | 32/46页 |
| 文件大小： | 498K |
| 描述： | IC LATCH CMOS MP TO-92UA |
| 产品目录绘图： | UA-92 Series Side |
| 标准包装： | 1,000 |
| 传感范围： | 9.5mT 跳闸，-9.5mT 释放 |
| 类型： | 双极卡锁 |
| 电源电压： | 3.5 V ~ 24 V |
| 电流 - 电源： | 5mA |
| 电流 - 输出（最大）： | 50mA |
| 输出类型： | 数字式，开漏极 |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | TO-226-3，TO-92-3 短体 |
| 供应商设备封装： | TO-92UA |
| 包装： | 散装 |
| 产品目录页面： | 2792 (CN2011-ZH PDF) |
| 其它名称： | US1881LUA US1881LUA-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
Section 3 - Applications
3-18
Programmable Isolated Current Sensor
Hall Effect Sensors can be used in conjunction with an electromagnet to make a very efficient, isolated
current-sensing device. This can be used to protect components from damage such as overheating.
The only components needed, as in Figure 13, are a Hall IC and a slotted ferrite toroid core driving an
indicator, relay or a logic-level fault signal. The ideal Hall IC in this application is a programmable linear
device, which would allow accurate calibration of the sensor and also versatility. For example, the dia-
gram below shows a toroid with 4 turns of wire. If a current of 10A was applied to the coil, the field at
the sensor would be about 6mT. The Hall IC can be programmed to give the desired response to this mag-
netic range. If the desired voltage swing is 0.5V (or 500mV) and the magnetic swing is 6mT, then the
device can be programmed to
83mV/mT to give the correct
response.
By varying the number of
windings and the programming
codes, rages as small as 100mA
and as large as 500A can be
achieved.
If used with a linear Hall-Effect
sensor, the output voltage will
be proportional to the current
flowing through the windings
on the toroid. This Voltage can
be used to indicate current
level, or trigger a shut-down
circuit.
Current Indicator/Limiter
If only a current indicator or limiter is needed, a simple circuit can be built with a Hall switch, and requires
no programming. In Figure 13, each complete turn of coil around the core, with a current of 1 Amp flow -
ing through it, will produce a flux density of approximately .6 mT upon the Hall Effect Switch. By adjust-
ing the number of coil turns around the core, the Hall Effect switch can act as either a current indicator or
current limiter.
Example:
Under normal operation a current of 10 Amps is delivered to a motor by some wire. Wrapping four turns
of the wire around the core will produce a magnetic field of 24 mT upon the Hall IC, which will activate
the device to ON. This can be used to illuminate an LED to symbolizing normal current. The LED will
remain ON until the field drops to about 18mT or about 7.5 Amps.
To use as a limiter, simply drop one turn of wire, which will require a higher current to turn the Hall switch
ON. With 1 turn removed, the switch will require 13 Amps to turn ON, and will remain on until the cur-
rent level drops below 1Amp.
PTC
TM
Figure 18, Programmable Current Sensor
相关PDF资料 |
PDF描述 |
|---|---|
| R7202206XXOO | RECTIFIER 2200V 600A |
| MDD250-08N1 | MOD DIODE DUAL 800V Y2-DCB |
| 601W-60 YEL | LEAD TEST MINIHK-BANAPLG 60" |
| US4881EUA-AAA-000-BU | IC LATCH CMOS H-SENS TO-92UA |
| US1881EUA-AAA-000-BU | IC LATCH CMOS MP TO-92UA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| US18-PA-5-N03-IH | 制造商:IDEC CORPORATION 功能描述:95B040020 Sensor Ultrasonic |
| US18-PA-5-N03-OH | 制造商:IDEC Corporation 功能描述:SENSOR, M18 STRGHT BARREL NPN/PNP OUTPUT 制造商:IDEC Corporation 功能描述:95B040000 Ultrasonic M18Sensor |
| US18-PA-5-N03-VH | 制造商:IDEC Corporation 功能描述:95B040040 Ultrasonic M18Sensor |
| US18-PR-5-N03-IH | 制造商:IDEC Corporation 功能描述:95B040030 Sensor Ultrasonic |
| US18-PR-5-N03-OH | 制造商:IDEC Corporation 功能描述:95B040010 Sensor Ultrasonic |
发布紧急采购，3分钟左右您将得到回复。